Sorting Devices for the CSC Muon Trigger System at CMS Matveev M., Padley P. matveev@physics.rice.edu Rice University, Houston, TX, USA Abstract Key components of the CMS Cathode Strip Chamber (CSC) Endcap Muon trigger system are the Muon Port Cards and Muon Sorter, which perform data selection and sorting. They implement sorting "3 best objects out of 18" and "4 best objects out of 36" schemes respectively. We report on a common approach to design and construction of both boards. Board functionality and first results of logic simulation and latency estimate are presented. Summary The front end electronics of the Cathode Strip Chamber (CSC) Endcap Muon detector at the CMS experiment needs to calculate precise muon position and timing information and generate muon trigger primitives for the Level-1 trigger system. CSC trigger primitives (called Local Charged Tracks, LCT) are formed by anode (ALCT) and cathode (CLCT) cards. ALCT cards are mounted on chambers, while CLCT cards are combined with the Trigger Motherboards (TMB) that perform a time coincidence of ALCT and CLCT. Every CLCT/TMB card (one per chamber) transmits the two best combined anode and cathode muon tags to the Muon Port Card (MPC) which serves one CSC sector (8 or 9 chambers). The MPC selects the three best muons out of 18 possible and sends them over 100m of optical cable to the Track Finder (TF) crate residing in the underground counting room. In the current electronics layout the TF crate has 12 Sector Processors (SP), each of which receives the optical streams from several MPC. The SP measures the transverse momentum, pseudo-rapidity and azimuthal angle of each muon and sends its data (up to 3 muons each) to CSC Muon Sorter (MS) that resides in the middle of the TF crate. The MS selects the four best muons out of 36 possible and transmits them to Global Muon Trigger crate for further processing. Two devices in the CSC trigger chain perform data sorting: the MPC ("3 best muons out of 18") and the MS ("4 best muons out of 36"). The total data reduction factor is 54. We propose a common approach to implementation of sorting logic and board construction for both the MPC and MS. They will be based on single chip programmable logic devices that receive data from the previous trigger level, sort it and transmit sorting result to the next trigger level. Programmable chips will incorporate input and output FIFO buffers that would represent all possible inputs and outputs for testing and debugging purposes. Finally we will use a common sorting scheme for both designs. The MPC and MS functionality as well as the first results of logic simulation and latency estimate are presented. ---------------------------------------------------------------------------- Optical Link Evaluation for the CSC Muon Trigger at CMS Matveev M., Nussbaum T., Padley P. Rice University, Houston, TX, USA Abstract An optical link intended for trigger data transmission from the CMS Cathode Strip Chamber peripheral electronics to the counting room was evaluated. It is based on a Texas Instruments TLK2501 gigabit transceiver and a Finisar FTRJ-8519-1-2.5 optical module. Functionality of the evaluation board and results of tests are presented. Summary The CMS Cathode Strip Chamber electronic system consists of on-chamber mounted boards, the peripheral electronics in VME 9U crates, and a Track Finder in the counting room. Due to high operating frequency of 40.08MHz and the 100m cable run from the detector to the underground counting room an optical link is the only choice for data transmission between these systems. Our goal was to prototype an optical link intended for the communication between the Muon Port Card and Sector Processor modules using existing commercial components. Our initial design based on the Agilent HDMP-1022/1024 chipset and Methode MDX-19-4-1-T optical transceivers was reported at the 6th Workshop on Electronics for LHC Experiments a year ago. Data transmission of 120 bits representing three muons at 40 MHz would require as many as twelve HDMP chipsets and twelve optical transceivers on a single receiver card (the Sector Receiver). This solution has disadvantages such as a large power consumption and a significant area required for link components on both the transmitter and receiver boards. Studies of the later triggering stages show that a reduction in the number of bits representing three muons can be made without compromising the system performance. Another improvement is to utilize a data serialization and deserialization at 80Mhz using a low power chipset and small form factor optical modules for a more compact design. Now only three links rather than six in a previous design are needed for communication between the Muon Port Card and Sector Processor. Results of the evaluation of the Texas Instruments TLK2501 gigabit transceiver and Finisar FTRJ-8519-1-2.5 optical module are reported. Low Voltage Control for the Liquid Argon Hadronic End-Cap Calorimeter of ATLAS H.Brettel*, W.D.Cwienk, J.Fent, H.Oberlack, P.Schacht MAX-PLANCK-INSTITUT FUER PHYSIK Werner-Heisenberg-Institut Foehringer Ring 6, D-80805 Muenchen Abstract The strategy of the ATLAS collaboration foresees a SCADA system for the slow control and survey of all sub-detectors. As software PVSS2 has been chosen and for the hardware links a CanBus system is proposed. For the Hadronic Endcaps of the Liquid Argon Calorimeter the control system for the low voltage supplies is based on this concept. The 320 preamplifier and summing boards, containing the cold front-end chips, can be switched on and off individually or in groups. The voltages, currents and temperatures are measured and stored in a database. Error messages about over-current or wrong output voltages are delivered. *Corresponding author, E-mail: brettel@mppmu.mpg.de Summary The slow control of sub-detectors and components of ATLAS is realized by a SCADA software installed in a computer net. At present it is PVSS2 from the Austrian company ETM. Links between net nodes and hardware are realized in different ways. Between the last node and the detector electronics a CanBus is foreseen in some cases for the transfer of control signals and the survey of temperatures, supply voltages and currents. An example are the Hadronic End Caps of the Liquid Argon Calorimeter. The application software in a PC, called PVSS2-project, has a connection to the CanBus via a driver software OPC and an interface board NICAN2 and acts as bus master. CanBus slaves are offered by the industry for several purposes. We use the ELMB from the CERN DCS group, which is tailored to our needs. It has 2 microprocessors inside and digital and analog I/O ports. Each of the two HEC-wheels consists of 4 quadrants served by a feed-through with a front-end crate on top of it. The low voltages for 40 PSBs , the preamplifier and summing boards which contain the cold GaAs front-end chips, are delivered by a power box, installed between the fingers of the Tile Calorimeter, about half a meter away from the crates. The input for a power box - a DC voltage in the range of 200 to 300V - is transformed into +8, +4 and -2V at the 3 output lines by DC/DC converters. At 2 control boards the lines are split into 40 channels, one for the supply of each PSB. Integrated low voltage regulators for each power line offer the possibility for individual adjustment and ON/OFF control. We use L4913 and L7913 from STm. The ELMBs and logic chips are mounted also on the control boards and establish the connection between the regulators and the CanBus. An ELMB has 8-bit digital I/O ports. In order to make the system architecture as simple as possible and increase reliability, only 5 of the 8 bits are used. One ELMB controls 5 PSBs which belong to the same longitudinal end-cap segment. The consequence is: if an ELMB would fail, only one longitudinal segment is affectedd.. The low voltage regulators have a current limitation. The maximal current is adjusted to such a low value, that the wires in the feed-through cannot be damaged in case of a steady short circuit inside the cryostat. In addition, in case of an over-current error signal from one regulator, the logic on the control board will switch off immediately all 3 low voltage regulators related to this channel. Then the control program is informed (via the CanBus) about details of the problem. Meanwhile tests of hard and software prototypes have been carried out successfully. The work on control boards is progressing and we are gaining more experience with the PVSS2 software.We are considering also an emergency control system, independent of the CanBus, for the case that a computer or the bus itself would fail. Front-end/DAQ interfaces in CMS Authors: G. Antchev, E. Cano, S. Cittolin, S. Erhan, W. Funk, D. Gigi, F. Glege, P. Gras, J. Gutleber, C. Jacobs, F. Meijers, E. Meschi, L. Orsini, L. Pollet, A. Racz, D. Samyn, W. Schleifer, P. Sphicas, C. Schwick Attila Racz Abstract In the context of the CMS data acquisition system, simple and robust data links are required to transfer data from the underground counting rooms up to the surface buildings where complex processing of the data takes place. In the case of CMS, ~500 of these links, with an individual throughput of 400MB/sec over a distance of 200m, is required. The interface specification for these links as well as recent hardware developments are presented in this paper. Summary After reviewing the architecture and design of the CMS data acquisition system, the requirements on the front-end data link and the different possible topologies for merging data from the front-ends are presented. The front-end data link is a standard element for all CMS sub-detectors: its physical specification as well as the data format/protocol are elaborated within the Readout Unit Working Group where all sub-detectors are represented. The current state of the link definition is covered. Finally, prototyping activities towards the final link as well as test/readout devices for Front-End designers and DAQ developers are described. Distributed Modular RT-System for Detector Control, DAQ and Trigger processing Dr.Sci. Vyacheslav Viniogradov Institute for Nuclear Research RAS prosop.60-let october 7-a , Moscow, 117312 Russia ( 3340190 fax 3340184 Abstract Modular approach to development of Distributed Modular System Architecture for Detector Control, Data Acquisition and Trigger Data processing is proposed. Multilevel parallel-pipeline Model of Data Acquisition, Processing and Control is proposed and discussed. Multiprocessor Architecture with SCI-based Interconnections is proposed as good high-performance System for parallel-pipeline Data Processing. Tradition Network (Ethernet -100) can be used for Loading, Monitoring and Diagnostic purposes independent of basic Interconnections. The Modular cPCI -based Structures with High-speed Modular Interconnections are proposed for DAQ and Control Applications. Distributed Control RT-Systems. To construct the Effective (cost-performance) systems the same platform of Intel compatible processor board should be used. Basic Computer Multiprocessor Nodes consist of high-power PC MB (Industrial Computer Systems), which interconnected by SCI modules and link to embedded microprocessor-based Sub-systems for Control Applications. Required number of Multiprocessor Nodes should be interconnected by SCI for Parallel-pipeline Data Processing in Real Time (according to the Multilevel Model) and link to RT-Systems for embedded Control/ Name: LEB20001 Stockholm.doc LEB20001 Stockholm.doc (application/msword) Type: Microsoft Word Document Encoding: base64 Download Status: Not downloaded with message Subject: [Fwd: Aliyev F.F] Date: Thu, 19 Apr 2001 12:27:31 +0200 From: Sam Silverstein Organization: Stockholm University Department of Physics To: Catherine.Decosse@cern.ch Catherine, This abstract and figure were sent to me directly without comment. Are you presently handling paper submissions for LEB? Sam Silverstein Stockholm University silver@physto.se --------------------------------------------------------------------- Subject: Aliyev F.F Date: Thu, 19 Apr 2001 15:16:09 +0400 From: "Bagirov.S" To: silver@physto.se Name: Concentration .doc Type: Microsoft Word Document Concentration .doc (application/msword) Encoding: base64 Download Status: Not downloaded with message [Image] Subject: Second try Date: Fri, 20 Apr 2001 13:53:22 +0200 From: Sam Silverstein Organization: Stockholm University Department of Physics To: catherine.decosse@cern.ch Catherine, Sorry about the last mail. I am still using VMS mail, and I forgot what it does to attachments... Sam --------------------------------------------------------------------- Subject: tezis Date: Fri, 20 Apr 2001 12:21:24 +0400 From: salima To: silver@physto.se --------------------------------------------------------------------- Name: stok.doc stok.doc Type: Microsoft Word Document (application/msword) Encoding: base64 Subject: LEB STOCKHOLM 2001 summary Date: Thu, 26 Apr 2001 15:48:38 +0200 From: Bjorn HALLGREN Organization: CERN To: Catherine.Decosse@cern.ch CC: Hallvard Kvedalen , Helfried BURCKHART Dear Mme Decosse, please find enclosed our contribution to the LEB 2001. Title: "The Embedded Local Monitor Board in the LHC Detector Front-end I/O Control System" Authors: B. Hallgren, H. Burckhart, H. Kvedalen CERN, EP-ATI/CS Best regards Bjorn Hallgren --------------------------------------------------------------------- Title: "The Embedded Local Monitor Board in the LHC Detector Front-end I/O Control System" Authors: B. Hallgren, H. Burckhart, H. Kvedalen CERN, EP-ATI/CS ABSTRACT The ELMB is a plug-in board to be used in LHC detectors as a general-purpose system for the front-end control and monitoring. It is based on CANbus, is radiation tolerant and can be used in magnetic fields. Results of the radiation tests will be presented and examples of applications will be described. SUMMARY A versatile general-purpose system for the front-end detector control, the Local Monitor Box (LMB) was designed in 1998 and tested by the ATLAS sub-detector groups in test-beam and other applications. With this experience and to match better all the needs of the ATLAS sub-detector groups a modified version, the Embedded Local Monitor Board (ELMB) was designed. The main feature of the ELMB is that the ELMB now comes in the form of a general- purpose plug-in board of the size 50x67mm. The board can either be directly plugged onto the sub-detector front-end electronics, or onto a general-purpose motherboard which adapts the analog I/O signals. In order to make the ELMB available to ATLAS and other LHC experiments, which have also expressed interest, a small scale production of 300 boards for evaluation has been made by the CERN EP-ESS group in spring 2001. The ELMB is based on the ATMEL low-power RISC microcontroller ATmega103. A second microcontroller AT90S2313 performs in system programming and monitoring functions including radiation Single Event Effects. A separate controller the Infineon SAE81C91 is used for the CANbus. The CANopen protocol has been chosen as high-level software. The ELMB can be powered remotely with the help of three low-drop power regulators. The power needed is 5V, 20 mA for the CANbus, 3.3V, 15 mA for the microcontrollers and 5V, 10mA for the ADC. The regulators function also as low-pass filters and provide current limitation and thermal protection for the ELMB. On the backside of the PCB are two high-density connectors of SMD type and optionally a 16+7 bit delta-sigma ADC with 64 differential inputs. There are up to 34 digital I/O lines available. The ATmega103 runs at a clock speed of 4 MHz. It has 128 kbytes of on-chip flash memory, 4 kbytes of SRAM and 4 kbytes of EEPROM. Also when the ELMB is installed in the detector it is possible to program the flash memory of the processors using the In-System Programming feature of the processors via the CAN bus. A motherboard is available in order to evaluate the ELMB and for non-embedded applications. On the backside it contains two 100-pin SMD connectors for the ELMB and sockets for adapters for the 64 channel ADC. There are adapters available for different temperature sensors like NTC resistors, 2 wire Pt1000 and 4 wire Pt100 sensors. The motherboard may be mounted in DIN rail housing of the size 80 x 190 mm. On the front side there are connectors for the ADC inputs, digital ports, a SPI interface, CAN interface and power connectors. The environmental requirements are such that it can be used in the ATLAS cavern (USA15) outside of the calorimeter in the area of the muon detectors (MDTs) and further out. This implies tolerance to radiation up to about 5 Gy and 3E10 neutrons/cm2 for a period of 10 years and to a magnetic field up to 1.5 T. Several radiation tests of the ELMB have been made following the procedures as laid out by the ATLAS radiation policy. The results of TID tests made at Pagure, Saclay and GIF, CERN with different dose rates will be reported. Further neutron testing at Prospero and SEE tests at Cyclone/Louvain-la-Neuve are planned for spring and summer 2001. The ELMB was also tested for a week at 100 degrees for accelerated ageing corresponding to 40000h at 25 degree C. Subject: LEB 2001 contribution Date: Thu, 26 Apr 2001 16:25:00 +0200 From: Adriano lai To: Catherine.Decosse@cern.ch CC: Sandro Cadeddu Dear M.me Decosse, Please find below our abstract and summary, concerning a contribution to the next LEB workshop. Best regards, Adriano Lai. ------------------------------------------------------------------------ DIALOG: an Integrated Circuit for front-end Logics, Diagnostics and Time Alignment in the LHCb muon system. S. Cadeddu, A. Lai* INFN Sezione di Cagliari, Cittadella Universitaria, 09042 Monserrato (Cagliari) - Italy *Corresponding author, tel +39-070-6754913, email adriano.lai@ca.infn.it. Abstract We present a custom integrated circuit, developed in the IBM 0.25 micron technology. The chip is named DIALOG ((DIagnostics, time Adjuster and LOGics) and it is a fundamental ingredient of the LHCb muon front-end electronics. Each integrated circuit handles 16 front-end channels. The circuit generates the information used by the level 0 trigger starting from the front-end signals, by means of a suitable (programmable) logical combination. In addition, it integrates functionalities important for signal time-alignment and front-end channels diagnostics at run time. Summary The LHCb muon system supplies binary information, used by the fast L0 muon trigger. Nevertheless, the information used by the trigger does not coincide with the signals as output by the front-end Amplifier-Shaper-Discriminators (ASD). This is due to single channel maximum capacitance and sustainable rates. So, an important task of the electronics system is to generate trigger information, corresponding to 26,000 so called logical channels, starting from about 120,000 ASD signals, called physical channels. In order to minimize the number of links (and costs), such a function is performed on detector by DIALOG, our custom integrated circuit. The logical combinations necessary to generate the logical channels are different, according to the different detector regions. Consequently, DIALOG is configurable by writing suitable internal registers, which are accessible via an I2C interface. DIALOG is also important to time-align logical channels, in order to correctly synchronize the entire detector. This task is crucial for all the LHC experiments. DIALOG integrates 16 programmable delays, which allow shifting the signal phase by 32 steps of about 1.5 ns each. This covers two bunch-crossing periods. The programmable delays are used when setting up the detector before data taking, but can be re-programmed at any needed time by writing suitable internal registers. DIALOG contains also diagnostics features to distribute synchronous pulses to the ASD channels and to monitor the physical channels' activity. Moreover, it contains DAC's to supply voltage thresholds to the front-end discriminators. All these functions are controlled via the I2C interface. DIALOG is being developed in the IBM 0.25 micron radiation hard technology. We plan to submit a first version in the next August run. We present the circuit internal scheme and layout and some characterizing simulations. ------------------------------------------------------------------------------- -- ____________________________________________________________ Adriano Lai I.N.F.N. Cagliari TEL. off. +39 070 675 4913 * labs. +39 070 675 4973/5/8 FAX +39 070 510212 http://www.ca.infn.it/~elettro TEL. @ CERN +41 22 76 74968 - Bat. 14-04-005 ____________________________________________________________ Subject: Re: call for paper LECC2001 Date: Thu, 26 Apr 2001 16:55:00 +0200 (MET DST) From: "C. De La Taille" To: Catherine DECOSSE CC: Bill Cleland , Philippe FARTHOUAT , Peter Schacht , Laurent Serin Bonjour Catherine, Voici l'abstract de la presentation que je souhaite faire au LEB7 (pour une fois je suis en avance de qq jours !) Amicalement : Christophe "A 10uV-offset DMILL opamp for ATLAS LAr calorimeter C. de La Taille, J.P. Richer, N. Seguin-Moreau, L. Serin LAL Orsay FRANCE In order to calibrate the LAr calorimeter to 0.25% accuracy, precision pulsers have been designed to provide a fast and precise pulse that simulates the detector pulse over its full 16bit dynamic range. They are based on a precision DC current source (2?A-200mA) built with a low offset opamp and a 0.1% 5ohm external resistor. Several COTs having failed the irradiation tests, a custom chip has been designed and fabricated, first in AMS 0.8um BiCMOS and then in DMILL. It has been successfully tested and the electrical performance and irradiation results will be shown." +----------------------------+------------------------------------------+ | Christophe de LA TAILLE | Laboratoire de l'Accelerateur Lineaire | | taille@lal.in2p3.fr | Centre d'Orsay - bat 200 | | Tel: (33) 1 64 46 89 39 | F 91 898 ORSAY Cx | | Fax: (33) 1 64 46 89 34 | | +----------------------------+------------------------------------------+ On Tue, 24 Apr 2001, Catherine DECOSSE wrote: > 7th WORKSHOP ON ELECTRONICS FOR LHC EXPERIMENTS > STOCKHOLM, Sweden, 10-14 September 2001 > > =========================================================== > REMINDER: DEADLINE for submission of Abstracts is April 30 !!!! > =========================================================== > > http://www.sysf.physto.se/leb2001 > > Regards > Catherine Decosse > > --------------------------------------------------------------------------- > 7th Workshop on Electronics for LHC Experiments > 10-14 September 2001, Stockholm, Sweden > > CALL FOR PAPERS > --------------- > > The purpose of the workshop is to review the electronics for LHC experiments > and to identify areas and encourage common efforts for the development of > electronics within and between the different LHC experiments and to promote > collaboration in the engineering and physics communities involved in the > LHC activities. > > The programme of the workshop will include both invited plenary talks and > parallel working groups for contributed papers, complemented by a poster > session. > The focus of the workshop will be research and recent development in the > following topics: > > Radiation and magnetic field tolerant electronics systems > Optoelectronics and data transfer systems > Detector control and real time systems > Packaging and interconnections > Electronics production and test techniques > Systems reliability and quality assurance > Hardware and embedded software maintenance > Electronics for trackers > Electronics for calorimeters > Electronics for muon detectors > Trigger electronics > Low voltage and high voltage distribution > Grounding, shielding cooling and alignment > > Authors are invited to submit papers describing original developments and > new contributions in the topic areas. Manufacturers are welcome to submit > abstracts on new, state of the art, electronic products or systems, > in the field of electronic technology for particle physics. > > Abstracts (100 words long) and summaries (500 words long) in ASCII format > and without figures must be submitted by electronic mail to: > > Catherine Decosse > Email: Catherine.Decosse@cern.ch > > The summary should be complete and describe the work, its relevance > to experiments at LHC (including specific experiment(s) if applicable) > and important conclusions. > > > Deadline for the submission is: > 30 April 2001 > > An acknowledgement will be sent by Email to the corresponding Author. > > Abstracts and summaries will be made available at the time of the workshop: > these will include papers which cannot be granted an oral presentation because > of time constraints but which, in the view of the programme committee, > are of interest to the community. Workshop records will be made available. > > Workshop Secretariat: > > Samuel Silverstein > University of Stockholm > Department of Physics > Box 6730, SE-113 85 STOCKHOLM > Email: silver@physto.se > tel. +46 8 16 46 65 > fax. +46 8 16 45 80 > > Any further information and news on the workshop will be provided > at the following URL address : > > http://www.physto.se/leb2001 > > To be registered in our database of the workshop, > please email your name and address to : > > Jonas Klereborn > Email: klere@physto.se > > > -- > _____________________________________________________ > Catherine DECOSSE > CERN > Alice Experiment > CH-1211 Geneva 23 > > Office: 301 R-035 > Tel. +41 22 767 36 77 > Fax. +41 22 767 94 80 > Subject: LEB 2001 Date: Thu, 26 Apr 2001 17:42:01 +0200 From: "Paulo Moreira" Organization: CERN To: Dear Catherine, please find attached the abstract and summary of my contribution to the LECC 2001 work shop. Best regards, Paulo Name: PauloMoreiraLEB2001.txt PauloMoreiraLEB2001.txt Type: Plain Text (text/plain) Encoding: quoted-printable Subject: Abstract for LEB2001 Date: Thu, 26 Apr 2001 22:06:35 +0200 (METDST) From: Daniel Baumeister To: Catherine.Decosse@cern.ch Dear Catherine, I hereby submit my abstract and summary for a contribution to the LEB2001 workshop. You will find the files in the mail body as well as attached. Best regards Daniel Author: ------ Daniel Baumeister baumeis@asic.uni-heidelberg.de MPI for Nuclear Physics Heidelberg ASIC laboratory Schroederstr. 90 D-69120 Heidelberg Phone: ++49 6221 544324 Fax : ++49 6221 544345 Title: ----- Performance of the Beetle Readout-Chip for LHCb Authors list: ---------- Niels van Bakel, Jo van den Brand, Hans Verkooijen (Free University of Amsterdam / NIKHEF Amsterdam) Daniel Baumeister, Werner Hofmann, Karl-Tasso Knoepfle, Sven Loechner, Michael Schmelling (Max-Planck-Institute for Nuclear Physics, Heidelberg) Martin Feuerstack-Raible (University of Heidelberg) Neville Harnew, Nigel Smale (University of Oxford) Edgar Sexauer (now at Dialog Semiconductors, Kirchheim-Nabern, Germany) Abstract: -------- The Beetle front end chip for LHCb is a 128 channel pipeline chip developed in 0.25 um standard CMOS technology. After intensive testing of the first version (Beetle1.0), an improved design (Beetle1.1) has been submitted in March 2001. The key measurements on the Beetle1.0, which mainly drove the design changes for the Beetle1.1, are described together with first performance data of the new chip. Summary: ------- A 128 channel readout chip, the Beetle, has been developed for the LHCb experiment in 0.25 um standard CMOS technology. The latest design has been submitted in March 2001. The chip can be operated as analog or alternatively as binary pipelined readout chip and fulfills the requirements of the silicon vertex detector, the inner tracker, the pile-up veto trigger and the RICH in case of multianode photomultiplier readout. The chip integrates 128 channels with low-noise charge-sensitive preamplifiers and shapers. The risetime of the shaped pulse is 25 ns, the spill-over left 25 ns after the peak at most 30%. A comparator per channel with configurable polarity provides a fast binary signal. Four adjacent comparator channels are being ORed and brought off chip via LVDS ports. Either the shaper- or the comparator output is sampled with the LHC-bunch-crossing frequency at 40 MHz into an analogue pipeline with a programmable latency of max. 160 sampling intervalls and an integrated derandomizing buffer of 16 stages. For analog readout the data are multiplexed with up to 40 MHz onto 1 or 4 ports. A binary readout mode operates with doubled output rate on two ports. Current drivers bring the serialized data off chip. The chip can accept trigger rates of up to 1 MHz, the readout time per event is within 900 ns. For testing and calibration purposes, a charge injector with adjustable pulse height is implemented. The bias settings and various other parameters can be controlled via a standard I2C-interface. The first chip version (Beetle1.0) submitted in April 2000 had to be patched with a focused ion beam to be functional. The reason was a layout bug in the control circuit. Beetle1.1 fixes this bug. In addition it solves a problem with the bias network of the pipeline readout amplifier, avoids charge injection in the switch of the resetable amplifier and fixes an error inside the multiplexer. The measurements pointing out bugs and problems on Beetle1.0 are presented, the resulting design modification on the Beetle1.1 are described and first performance measurements with the new readout chip are shown. -------------------------------------------------------------- Daniel Baumeister Phone: ++49 6221 544324 MPI fuer Kernphysik Fax : ++49 6221 544345 ASIC laboratory Email: baumeis@ Schroederstr. 90 asic.uni-heidelberg.de D-69120 Heidelberg -------------------------------------------------------------- --------------------------------------------------------------------- Name: authorslist.txt authorslist.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64 Name: summary.txt summary.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64 Name: abstract.txt abstract.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64 Subject: abstract for leb2001 Date: Thu, 26 Apr 2001 22:12:09 +0200 (CEST) From: John Dawson To: Catherine.Decosse@cern.ch CC: David.Francis@cern.ch, jls@hep.anl.gov, wnh@hep.anl.gov ---------- Forwarded message ---------- Date: Thu, 26 Apr 2001 22:05:48 +0200 (CEST) From: John Dawson To: jwd@atlas.cern.ch TTCPR: A PMC RECEIVER FOR TTC John W. Dawson, David J. Francis, William N. Haberichter, and James L. Schlereth Argonne National Laboratory and CERN The TTCPR receiver is a mezzanine card intended for use in distributing TTC information to Data Acquisition and Trigger Crates in the Atlas Prototype Integration activities. An original prototype run of these cards was built for testbeam and integration studies, implemented in both the PMC and PCI form factors, using the TTCrx chips from the previous manufacture. When the new TTCrx chips became available, the TTCPR was redesigned to take advantage of the availability and enhanced features of the new TTCrx, and a run of 20 PMC cards was manufactured, and has since been used in integration studies and the testbeam. The TTCPR uses the AMCC 5933 to manage the PCI port, an Altera 10K30A to provide all the logic so that the functionality may be easily altered, and provides a 4K deep FIFO to retain TTC data for subsequent DMA through the PCI port. In addition to DMA's which are mastered by the Add On logic, communication through PCI is accomplished via mailboxes, interrupts, and the Pass-thru feature of the 5933. An interface to the I2C bus of the TTCrx is provided so that internal registers may be accessed, and the card supports reinitialization of the TTCrx from PCI. Software has been developed to suport operation of the TTCPR under both LynxOS and Linux. Subject: Re: call for paper LECC2001 Date: Thu, 26 Apr 2001 15:39:04 -0500 From: Sergio Zimmermann To: Catherine DECOSSE CC: zimmer@fnal.gov Dear Catherine I would like to submit the paper below for the LECC2001. The corresponding author is myself, Sergio Zimmermann Fermi National Accelerator Laboratory P.O. Box 500 MS 368 Batavia, IL 60510 USA e-mail: zimmer@fnal.gov phone: (630) 840-4276 fax: (630) 840-8208 Thanks, Sergio Development of the Pixel Detector Module for the BTeV Experiment at Fermilab S. Zimmermann, J. Andresen, J.A. Appel, G. Cardoso, D.C. Christian, B.K. Hall, J. Hoff, S.W. Kwan, A. Mekkaoui, R. Yarema. Fermi National Accelerator Laboratory P.O. Box 500 Batavia, IL 60510 USA Abstract At Fermilab, a pixel detector multichip module is being developed for the BTeV experiment. The module is composed of three layers. The lowest layer is formed by the readout ICs. The back of the ICs are in thermal contact with the supporting structure while the other side is bump-bonded to the pixel sensor. A low mass flex-circuit interconnect is glued on the top of this assembly, and the readout IC pads wire-bounded to the flex circuit. This paper will present recent results on the development of a module prototype and summarize its performance characteristics. Summary At Fermilab, the BTeV experiment has been approved for the CZero interaction region of the Tevatron. The innermost detector for this experiment will be a pixel detector composed of 64 pixel planes of approximately 100 mm by 100 mm each, assembled perpendicular to the colliding beams and installed a few millimeters from the beams. Each plane is formed by sets of hybridized modules, each composed of a single active-area sensor and of one row of readout integrated circuits (ICs). The pixel detector will be employed for on-line track finding for the lowest level trigger system and, therefore, the pixel readout ICs will have to transfer data for all detected hits. This requirement imposes a severe constraint on the design of the readout IC, hybridized module, and data transmission. Several factors affect the amount of data that each IC needs to transfer: readout array size, distance from the beam, number of bits of pulse height information, the data format, etc. Presently, the most likely dimension of the pixel chip array will be 128 rows by 22 columns. The BTeV pixel detector module is based on a design relying on a hybrid approach. With this approach, the readout chip and the sensor array are developed separately and the detector is constructed by flip-chip mating the two together. This method offers maximum flexibility in the development process, choice of fabrication technologies, and the choice of sensor material. The module is composed of three layers. The lowest layer is formed by the readout ICs. The back of the ICs are in thermal contact with the supporting structure while the other side is bump-bonded to the pixel sensor. The low mass flex-circuit interconnect is glued on the top of this assembly and the readout IC pads wired-bounded to the flex-circuit. The module is remotely controlled by the pixel Data Combiner Board, located approximately 10 meters away from the detector. All the controls, clocks and data are transmitted between the pixel module and the data acquisition system by differential signals employing the LVDS standard. Common clocks and control signals are sent to each module and then bussed to each readout IC. All data signals are point to point connected to the Data Combiner Boards. A prototype module using the FPIX1 IC has been characterized. However, differently from the proposed "sandwich" module, the flex-circuit of this prototype is located on the side of the ICs. Typical results include threshold of 1500 electrons, threshold dispersion of 280 electrons and noise of 60 electrons. The comparison of these results with the characterization results of a single FPIX1 IC board shows no observed degradation in performance. Furthermore, tests with dead-time-less mode, where the charge inject in the front end is time swept in relation to the readout clock also does not reveal any degradation in performance, suggesting no crosstalk problems between the digital and analog sections of the FPIX1 IC and the flex-circuit. _____________ Sergio Zimmermann Computing Divison/Electronic Systems Engineering Dept. Fermi National Accelerator Laboratory P.O.Box 500, MS 368 Batavia, IL 60510 Phone: (630) 840-4276 Fax: (630) 840-8208 Subject: Paper submission for LEB2001 Date: Fri, 27 Apr 2001 11:46:38 +0900 From: Kazumi HASUKO To: Catherine.Decosse@cern.ch Dear Catherine, I would like to submit the following paper for the next LEB2001 workshop. Best regards, Kaz Hasuko __________________________________________________________________ Kazumi HASUKO e-mail: hasuko@icepp.s.u-tokyo.ac.jp International Center for Elementary Particle Physics (ICEPP) University of Tokyo 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033, JAPAN phone: +81-3-3815-8384 fax: +81-3-3814-8806 URL: http://www.icepp.s.u-tokyo.ac.jp/~hasuko/ -------------------------------------------------------------------- Paper submission -------------------------------------------------------------------- First Name: Kazumi Last Name: Hasuko E-mail hasuko@icepp.s.u-tokyo.ac.jp Institute: University of Tokyo Address: 7-3-1 Hongo Bunkyo-ku, Tokyo 113-0033 Country: JAPAN Experiment: ATLAS Topic: Detector control and real time systems Title: A Remote Control System for On-Detector VME Modules of the ATLAS Endcap Muon Trigger Author List: K. Hasuko(1), C. Fukunaga(5), R. Ichimiya(3), M. Ikeno(2), Y. Ishida(5), H. Kano(5), Y. Katori(1), T. Kobayashi(1), H. Kurashige(3), K. Mizouchi(4), Y. Nakamura(1), H. Sakamoto(4), O. Sasaki(2) and K. Tanaka(5) (1) International Center for Elementary Particle Physics (ICEPP), University of Tokyo (2) High Energy Accelerator Research Organization (KEK) (3) Department of Physics, Kobe University (4) Department of Physics, Kyoto University (5) Department of Physics, Tokyo Metropolitan University Abstract : We present the development of a remote control system for on-detector VME modules of the ATLAS endcap muon trigger. The system consists of a local controller in an on-detector VME crate and a remote interface in a Readout Driver crate. The controller and interface are connected with dedicated optical links based on G-LINK. The control system can fully configure and control modules, especially FPGA-embedded ones using G-LINK words and VME bus from remote host. The system supports periodical readback and reconfiguration to assure correct configuration data against SEUs. The idea, prototype and initial performance tests of the system are discussed. Summary : We present the development of a remote control system for on-detector VME modules of the ATLAS endcap muon trigger. Such the VME modules are Star Switch (SSW) and High-pT board (HPT); the remote control system fully controls and configures them from outside of detector. SSW is a relay module between on-detector modules and Readout Driver (ROD). SSW receives hit information from readout buffers in the modules, performs data reduction and formatting, and transfers the results to ROD. SSW is based on FPGAs which should be configured and controlled by the remote control system. Since the configuration data are susceptible to radiation-induced upsets (SEUs), dedicated control and configuration links are necessary, and every configuration should be assured to be correct via the links. The other module, HPT, is a part of trigger system. HPT is based on ASIC configured with some registers inside and fully controlled via the same links from outside. The remote control system consists of HPT/SSW Controller (HSC) and Control/Configuration Interface (CCI). HSC is a local controller in a HPT/SSW VME crate. CCI is a remote interface in a ROD crate. HSC communicates with the ROD host via CCI. HSC and CCI are connected with optical links based on G-LINK. The links are dedicated for control and configuration. The host manages an instruction set; each instruction is encoded into 14-bit G-LINK control word and executed on HSC. When downloading data, additional 16-bit data words are used. Following instructions, HSC can master the VME bus to access the HPT/SSW modules through VME protocol encoders implemented in CPLDs on both HSC and HPT/SSW modules. All the control and configuration are performed via VME accesses. FPGAs in SSWs are also configured via the VME bus using byte-based configuration scheme. To resist SEUs, configuration data are periodically read back. Once a SEU is detected, the accessed FPGA is instantly reconfigured. The CPLDs as VME protocol encoders are configured with JTAG provided on the VME backplane. These JTAG signals are in a bus structure and mastered by an embedded JTAG controller on HSC with dedicated instructions. Most of the HSC functionalities are also built using CPLDs; they are configured with the same JTAG bus. Only the core part of instruction encoders on HSC manages the JTAG-related instructions and built using an ASIC to resist SEUs. Therefore all the related CPLDs are configurable using the JTAG provided via the ASIC encoder. The detailed idea, prototype and initial performance tests of the HSC/CCI control system are discussed in this workshop. We will also discuss that the performance meets the requirements for controlling and configuration of HPT and SSW modules. Subject: abstract LEB Date: Fri, 27 Apr 2001 09:04:12 +0200 (MET DST) From: Susanne.Kersten@cern.ch To: CC: Dear Mrs. Decosse, please fine as an attachment the abstract for the talk we would like to present: "Development of a Detector Control System for the ATLAS Pixel Detector". The number of words in the abstract is 135, sorry. If we have to shorten it, please let me know. Title and preliminary author list can be seen in the attached file as well. Is it possible to send the summary a few days later? Best wishes, Susanne Kersten --------------------------------------------------------------------- Name: SK_abstract2.doc SK_abstract2.doc Type: Microsoft Word Document (application/msword) Encoding: BASE64 Subject: Submission to LEB2001 Date: Fri, 27 Apr 2001 16:45:45 +0900 From: Yasuo Arai To: Dear Catherine, I would like to submit a paper to the LEB 2001 workshop at Stockholm. Abstract and summary are attached below. Regards, Yasuo Arai ------------------------------------------------------------------------ KEK, National High Energy Accelerator Research Organization Institute of Particle and Nuclear Studies 1-1 Oho, Tsukuba, Ibaraki 305-0801, JAPAN tel +81-298-64-5366, fax +81-298-64-2580 yasuo.arai@kek.jp ------------------------------------------------------------------------ Paper Title : Production and Radiation Tests of A TDC LSI for the ATLAS Muon Detector Authors : Yasuo Arai KEK, National High Energy Accelerator Research Organization Institute of Particle and Nuclear Studies and T. Emura Tokyo University of Agriculture and Technology Abstract : ATLAS Muon TDC (AMT) LSI has been successfully developed and performance of a prototype chip (AMT-1) was reported in the LEB 2000. A new AMT chip (AMT-2) was developed aiming for mass production. The AMTs were processed in a 0.3 um CMOS Gate-Array technology, To proceed to a mass production of 400 k channels (~17,000 chips) scheduled in 2002, a systematic test methods must be established. Furthermore, the chip must be qualified to have adequate radiation tolerance in ATLAS environment. The test method and results of the radiation tests for gamma rays and charged particles will be presented. Summary : A TDC LSI for the ATLAS precision muon tracker (MDT) has been developed. The TDC chip, called AMT, was processed in a 0.3 um CMOS Gate-Array technology. It contains 24 input channels, 256 words level 1 buffer, 8 words trigger FIFO and 64 words readout FIFO. It also includes trigger-matching circuit, which selects data according to a trigger. The selected data are transferred through 40 Mbps serial line. By using a Phase Locked Loop (PLL) circuit, it achieved 300 ps timing resolution. The chip is packaged in a 144 pins plastic QFP with 0.5 mm pin pitch and about 110k gates are used. A prototype chip, AMT-1 was successfully tested and reported in the last LEB workshop. The AMT-1 was mounted in a front-end PC board with ASD (Amp/Shaper/Discri) chips, and system tests connected to a detector have been done (submitted in this workshop). A mass-production prototype chip, AMT-2, has been recently developed. Although the AMT-1 was successfully operated, it consumed relatively large power in inside LVDS receiver circuits. A low-power LVDS receiver was developed and included in the AMT-2. In addition, testability was enhanced and several minor bugs are also fixed. Mass production of 400 k channels (~17,000 chips) are scheduled in an early period of 2002. Most of the chip tests are done in manufacture, but a systematic test system are still needed. Furthermore the chip must be qualified to have adequate radiation tolerance in ATLAS environment. Gamma-ray irradiation to measure Total Ionization Damage (TID) and proton irradiation to measure Single Event Effects (SEE) are planned. Test methods and results of the radiation tests will be presented. Subject: Paper Submission to the 7th Workshop on Electronics for LHC Experiments. Date: Fri, 27 Apr 2001 17:36:37 +0900 From: imori To: Catherine.Decosse@cern.ch Dear Madam; I would like submit a paper entitled "Network-Controlled High Voltage Power Su pplies Operating in Magnetic Field" to the 7th Workshop on Electronics for LHC Experiments. Abstract and Summary are attached in the following. Best regards, Masatosi Imori ICEPP University of Tokyo 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 Japan Tel: +81 3 3815 8384 Fax: +81 3 3814 8806 E-mail: imori@icepp.s.u-tokyo.ac.jp Abstract The article describes a network of high voltage power supplies which can work efficiently under a magnetic field of 1.5 tesla. The high voltage power supply incorporates a piezoelectric ceramic transformer. The power supply includes feedback to stabilize the high voltage output, supplying from 2000V to 4000V with a load of more than 20 megohm at efficiency higher than 50 percent. The high voltage power supply includes a Neuron chip, a programming device processing a variety of input and output capabilities. The chip can also communicate with other Neuron chips over a twisted-pair cable, which allows establishing a high voltage control network consisting of a number of power supplies each of which incorporates the chip individually. The chip sets the output high voltage. The chip detects the short circuit of the output high voltage and controls its recovery. The chip also monitors the output current. The functions of the power supply under the control of the chip are managed through the network. The high voltage power supplies are networked, being monitored and controlled through the network. Summary Network-Controlled High Voltage Power Supplies Operating in Magnetic Field High Voltage Power Supply The article describes a network of high voltage power supplies. The high voltage power supply includes feedback to stabilize the high voltage output, supplying from 2000V to 4000V with a load of more than 20 megohm at efficiency higher than 50 percent. The power supply incorporates a ceramic transformer. So the power supply can be operated efficiently under a magnetic field of 1.5 tesla. The power supply could be utilized in LHC experiments. The power supply includes an error amplifier and a voltage-controlled oscillator (VCO). The output voltage is fed to the error amplifier to be compared with a reference voltage. The output of the error amplifier is supplied to the VCO which generates the frequency of a carrier where the carrier drives the ceramic transformer. Voltage amplification of the transformer depends on the frequency of the carrier. So the feedback adjusts magnitude of the amplification by controlling the frequency. Breakdown of Feedback While the load of the power supply falls within an allowable range, the driving frequency is maintained higher than the resonance frequency of the transformer such that the feedback is negative as designed. The allowable range of load cannot cover, for example, short-circuiting the output high voltage to ground. When the load deviates beyond the allowable range, the driving frequency may decrease below the resonance frequency; a condition that will not provide the required negative feedback, i.e., positive feedback locks the circuit such that it is independent of load. Network The high voltage power supply includes a "Neuron" chip possessing a variety of input and output processing capabilities. The Neuron chip can communicates with other Neuron chips over a twisted-pair cable; a feature that allows establishing a network consisting of a number of power supplies that respectively incorporate the chip. Since most functions of the power supply is brought under the control of the chip, the power supplies are managed via the network. Output High Voltage The reference voltage is generated by a digital-to-analog converter controlled by the chip so that the output high voltage can be controlled by the network. Recovery from Feedback Breakdown The VCO voltage, being the output of the error amplifier, controls the driving frequency of the carrier. The feedback breakdown is produced by deviation of the VCO voltage from its normal range. The deviation is detected by voltage comparators, interrupting the Neuron chip. Once awakened, the chip reports the feedback breakdown and manages the power supply so as to recover from the breakdown. Current Monitor If both the output high voltage and the supply voltage are known before hand, the frequency at which the transformer is driven depends on the magnitude of the load. The output current can be estimated from the driving frequency. The chip gets the driving frequency by counting pulses, which allows calculating the output current. References M. Imori, T. Taniguchi and H. Matsumoto, "Performance of a Photomultiplier High Voltage Power Supply Incorporating a Piezoelectric Ceramic Transformer," IEEE Trans. Nucl. Sci., vol. 47, no. 6, pp. 2045-2049, Dec. 2000. Y. Shikaze, M. Imori, H. Fuke, H. Matsumoto and T. Taniguch, "Performance of a High Voltage Power Supply Incorporating a Ceramic Transformer, "Proceedings of the 6th Workshop on Electronics for LHC Experiments, pp.371-375, Sept. 2000, Krakov, Poland, To be published in IEEE Trans. Nucl. Sci. Subject: Leb2001 abstract Date: Fri, 27 Apr 2001 11:07:08 +0200 From: vicente gonzalez To: catherine.decosse@cern.ch Title: "On the developments of the Read Out Driver for the ATLAS Tile Calorimeter" Authors: Jose Castelo, Vicente Gonzalez, Enrique Sanchis Afiliation: IFIC and Dpt of Electronic Engineering. University of Valencia Abstract: "This works describes the present status and future evolution of the Read Out Driver for the ATLAS Tile Calorimeter. The developments currently under execution include the test of the adapted LAr ROD to Tile Cal needs and the design and implementation of the PMC board for algorithm testing at ATLAS rates. We will describe the test performed at University of Valencia with the LAr ROD motherboard and a new developped transition module with 4 SLINK inputs and one output which match the initial TileCal segmentation for RODs. We will also describe the work going on with the design of a DSP based PMC with SLINK input for real time data processing to be used as a test environment for optimal filtering." We would like to present this work as a poster. Thank you. --------------------------------------------------------------------- Vicente González DSDC - Grupo de Diseño de Sistemas Digitales y de Comunicación Dept. Ingenieria Electronica. Universitat de Valencia Vicente González DSDC - Grupo de Diseño de Sistemas Digitales y de Comunicación Dept. Ingenieria Electronica. Universitat de Valencia Avda . Dr. Moliner, 50 Fax: +34 96 316 0466 Burjassot Work: +34 96 316 0453 Valencia 46100 Spain Additional Information: Last Name González First Name Vicente Version 2.1 Subject: call for stockholm paper Date: Fri, 27 Apr 2001 10:47:07 +0100 From: Nigel Smale To: "'Catherine.Decosse@cern.ch'" Hi Catherine, Another abstract and summary for you. <> Many thanks --------------------------------------------------------------------- Name: stockholm call for papers.txt stockholm call for papers.txt Type: Plain Text (text/plain) Encoding: quoted-printable Subject: paper for LECC2001 Date: Fri, 27 Apr 2001 13:12:17 +0100 From: Juan Andres de Agapito Reply-To: agapito@fis.ucm.es Organization: ucm To: Catherine.Decosse@cern.ch Please, enclosed fine a copy of the abstract and summary of the proposed paper "Radiation Tests on Commercial Instrumentation Amplifiers, Analog Sw., DAC's & ADC's " to LECC2001. Sincerely Juan A. de Agapito --------------------------------------------------------------------- Name: AbstractLHC2001.doc Type: Microsoft Word Document AbstractLHC2001.doc (application/msword) Encoding: Base64 Download Status: Not downloaded with message Subject: lecc2001 Date: Fri, 27 Apr 2001 08:52:10 -0400 From: helio takai Organization: Brookhaven National Laboratory To: Catherine.Decosse@cern.ch Hi Catherine, We would like to submit the attached abstract for the lecc2001 meeting in Stockholm. Cheers, Helio takai@bnl.gov --------------------------------------------------------------------- Development of Radiation Hardened DC-DC converters for the ATLAS Liquid Argon Calorimeter Helio Takai and James Kierstead Brookhaven National Laboratory The power supplies for the ATLAS liquid argon calorimeter using 300V input DC-DC converters will be located in a high radiation environment. Over the life of the experiment (i.e. 10 years) the total ionizing dose is expected to reach 25 krad. Along with the total dose is a projected total fluence of 2x10^12 particles/cm^2 of 1 MeV equivalent neutrons of which a fraction of the total neutron fluence, 1x10^11 neutrons/cm^2, has energies above 20 MeV. These values include the standard ATLAS recommended safety factors. The anticipated effects in order of potential seriousness are: (a) single event burnout (SEB) of the input power MOSFET, (b) total dose effects on active CMOS and bipolar components and (c) neutron induced lattice displacements causing conductivity and other changes in active components. The power supply will also be subjected to a magnetic field at a strength of 50 Gauss. Tests performed on commercially available modules manufactured by Vicor found that none satisfy the requirements. Therefore we are seeking a solution that involves a semi-custom design. This typically introduces questions of reliability and cost. The approach for the development of a prototype is to select a vendor with experience in designing power supplies for radiation environments, e.g. space environments. This provides some assurance that the power supply will be hardened to ionizing and neutron radiation. Then to reduce cost, the radiation hardened power MOSFET will be replaced with a less expensive commercial power MOSFET. It is known that by operating a commercial MOSFET at a lower (derated) voltage it is possible to use them safely in an environment with high-energy particles. For instance a 600 volt MOSFET operated at 500 volts might show a large SEB cross section but has a negligible SEB cross section at 300 volts. We will report on the progress of the design and comment on the different practical issues of the process such as purchasing of components in lots and specifying parts. Results of power MOSFET qualification will also be presented as well as preliminary test results. Packaging and operational issues will also be discussed as time allows. Subject: LEW2001 Poster Submission Date: Fri, 27 Apr 2001 14:53:11 +0200 From: Jean-Michel SAINSON Organization: CERN To: Catherine Decosse Madame, Could you please consider the following POSTER submission for workshop (LEW2001). Thank you very much. = = = Title: PRINTED CIRCUIT BOARD SIGNAL INTEGRITY ANALYSIS AT CERN Abstract: Because of increasing clock frequencies, faster rise times and wider busses, printed circuit board (PCB) design layout becomes an issue. The Cadence(r) SPECCTRAQuest(tm) SI (signal integrity) package allows the pre- and post-layout signal integrity analysis of a PCB designed in the Cadence flow under Allegro. Case studies of work done for some LHC detectors will be presented. These will show how the tools can help Engineers in design choice, optimizing electrical performance of board layout, to reduce prototype iterations and to improve production robustness. Examples will include work done on PCI 66MHz and GTL busses. -------------------------------------------------------------------- Jean-Michel Sainson SI Engineering & Support CERN - IT Division CE Group Phone:(41) 22 767 75 61 CH - 1211 Genève 23 Fax:(41) 22 767 71 55 SUISSE / SWITZERLAND mailto:J-M.Sainson@cern.ch Intranet: http://cern.ch/support-specctraquest/ -------------------------------------------------------------------- Subject: LEB 2001 Date: Fri, 27 Apr 2001 14:55:01 +0200 From: Michael BURNS To: Catherine DECOSSE The ALICE Pixel Detector Readout Chip Test System Antinori, F. (1,2), Ban, J. (3), BURNS, M. (1), Campbell, M. (1), CHOCHULA, P. (1, 4), Formenti, F. (1), Kluge, A. (1), Meddi, F. (1, 7), Morel, M. (1), Petra, Rober to, Snoeys, W. (1), Stefanini, G. (1), Wyllie K. (1). (For the ALICE Collaboration) ABSTRACT Described is a system that has been developed for testing the ALICE Silicon Pi xel Detector Readout Chip. It is capable of covering all aspects of testing, from the selection of know good dies on a waf er, characterisation, and as a DAQ when performing beam tests Considerable effort has been invested in the software to provide a comprehensi ve suit of facilities and test routines to enable the complete testing and characterisation of the device. In this paper we would like to present the objectives and requirements of the test system, a description of the hardware, software and database and present some of the results obtained. SUMMARY The previous test system for the pre prototype ALICE1LHC Pixel detector Readou t Chip was built using both CAMAC and VME components employing a standard processor that was sited in the VME cr ate. The system evolved continuously to increase the system functionality and automate the measurement process. Thi s resulted in a bulky test system which was difficult to transport and almost impossible to reproduce. The results of the measurements were stored on the VME system local disk for treatment at a later date by another computer system. The new system has taken the analogue functionality of the CAMAC modules and i ntegrated them into the circuitry contained on the Adapter Board. The VME crate had been kept and houses the mod ules required in the DAQ chain. A PC running LabView software has been selected as the system controller. The PC is interfaced to the VME system using the MXI bus connection from National Instruments The Adapter Board is controlled u sing a 4-wire JTAG connection from an interface which may be installed in either the PC or the VME crate. All test p arameters may be varied interactively to enable detailed verification of the various subsections of the Pixel Chip or r outines can be executed to automatically perform detailed measurements of the devices. Acquired data is treated and displayed via a graphical user interface exploiti ng the capabilities of LabView to rapidly present the results. The results may then archived for further reference when either assembling the Pixel Detector or by the ALICE online database. The system requires approximately xx minutes to characterise a device and yy m inutes to test a whole wafer automatically Subject: 7th Workshop on Electronics abstract submission Date: Fri, 27 Apr 2001 08:58:25 -0400 From: Nikolay Bondar Organization: Fermilab To: Catherine Decosse Dear Mrs. Catherine Decosse, That is paper for 7th Workshop on Electronics. If you have a question, welcome. With regards, Nikolay Bondar. 1. Abstract. Anode Front-End Electronics for the Cathode Strip Chambers of the CMS Endcap Muon Detector N. Bondar*, T. Ferguson**, A. Golyash*, V. Sedov*, N. Terentiev**. *) Petersburg Nuclear Physics Institute, Gatchina, 188350, Russia **) Carnegie Mellon University, Pittsburgh, PA, 15213, USA 7th Workshop on Electronics for LHC Experiments 10-14 September 2001, Stockholm, Sweden Abstract The very front-end electronics system for the anode signals of the CMS Endcap Muon cathode strip chambers has been designed. Each electronics channel consists of an input protection network, amplifier, shaper, constant-fraction discriminator, and a programmable delay with an output pulse width shaper. The essential part of the electronics is an ASIC consisting of a 16-channel amplifier-shaper-discriminator (CMP16). The ASIC was optimized for the large cathode chamber size (up to 3 m x 2.5 m) and for the large input capacitance (up to 300 pf). The ASIC combines low power consumption (30 mW/channel) with excellent time resolution (~2 ns). A second ASIC provides a programmable time delay which allows the alignment of signals with an accuracy of 2.5 ns. 2. Summary Anode Front-end Electronics for the Cathode Strip Chambers of the CMS Endcap Muon Detector N. Bondar*, T. Ferguson**, A. Golyash*, V. Sedov*, N. Terentiev**. *) Petersburg Nuclear Physics Institute, Gatchina, 188350, Russia **) Carnegie Mellon University, Pittsburgh, PA, 15213, USA 7th Workshop on Electronics for LHC Experiments 10-14 September 2001, Stockholm, Sweden Summary The very front-end electronics system for the anode signals of the CMS Endcap Muon cathode strips chambers has been designed. The main tasks of the anode side of the detector are to provide a good time resolution and a high efficiency. To meet this requirement, the following measures were implemented: -each channel was split into two parts: an analog section (amplifier-shaper-discriminator), followed by a digital delay and pulse width shaper. -the analog part was placed as close to the anode outputs as possible, and the digital part was located on the input of the anode local charged track board (ALCT). -the amplifier input circuits were very carefully arranged and shielded. Two ASICs were designed. The first is a 16-channel amplifier-shaper-discriminator (CMP16). The ASIC was optimized for the large chamber size (up to 3 m x 2.5 m) and for the large input capacitance (up to 300 pf). The ASIC combines low power consumption (30 mW/channel) with excellent time resolution (~2 ns). The chip is made by AMI, using a BiCMOS 1.5 micron technology. To achieve a low input resistance and relatively low noise, a BJT was used as an amplifier first stage. A two-exponent tail cancellation system, with a semi-Gaussian shaper is also employed in the chip. A two-thresholds constant-fraction discriminator is used to obtain the required time resolution. Output signal levels are LVDS standard. The second ASIC is a 16-channel LVDS/TTL converter, with a programmable delay and output pulse width shaper. This chip was also made by AMI, using a CMOS 0.5 micron technology. The chip is a logical extension of the CMP16 chip in that it matches the amplifier outputs to the ALCT logic inputs and aligns the signals in phase at the input of the anode logic. To support the CMP16 chip, a 16-channel anode front-end board (AD16) was also designed. The board was made in the simplest and cheapest way possible. The threshold control network and the board test facility were delegated to the ALCT board. Each AD16 board is connected to the ALCT board with a 40-wire cable. This cable supplies the board with power, a threshold voltage setting and test pulses, as well as transmits the output signals to the ALCT. A special setup and accompanying procedures were designed to test and certify the AD16 boards and the two ASICs. The anode front-end electronics system has met the required specifications, and the mass production has begun. Subject: LEB doc Date: Fri, 27 Apr 2001 17:58:06 +0200 From: Christoph POSCH Organization: CERN To: Catherine Decosse CC: Eric Hazen , John Oliver Hi Catherine, here comes abstract and summary of our LEB2001 article. cheers, Chr. C. Posch*, E. Hazen, J. Oliver: CMOS front-end for the MDT sub-detector in the ATLAS Muon Spectrometer, development and performance. Abstract Development and performance of the final 8-channel front-end for the MDT segment of the ATLAS Muon Spectrometer is presented. This last iteration of the read-out ASIC contains all the required functionality and meets the envisaged design specifications. In addition to the basic "amplifier-shaper-discriminator"-architecture, MDT-ASD uses a Wilkinson ADC on each channel for precision charge measurements on the leading fraction of the muon signal. The data will be used for discriminator time-walk correction, thus enhancing spatial resolution of the tracker, and for chamber performance monitoring (gas gain, ageing etc.). The feasibility of the MDT system to perform particle identification through dE/dX measurement using the Wilkinson ADC is evaluated. Results of performance and functionality tests in the lab and on-chamber along with an outlook to volume-production and production testing are presented. Summary This article reviews the development of the final 8-channel front-end for the MDT segment of the ATLAS Muon Spectrometer and presents results of performance and functionality tests on the last pre-production prototype. The MDT-ASD is an octal CMOS Amplifier/Shaper/Discriminator which has been designed specifically for the ATLAS MDT chambers. Implementation as an ASIC using a high quality analog 0.5um CMOS process has been chosen for this device. The analog signal chain of the MDT-ASD has already been presented for a previous prototype version of the chip and has not been changed significantly since then. It will therefore be addressed only briefly in this article. New developments include the implementation of a Wilkinson type charge-to-time converter and on-chip programmability of certain functional and analog parameters along with a serial control data interface. Bipolar shaping was chosen to prevent baseline shift at the anticipated level of background hits. The shaper output is fed into a discriminator for the timing measurement and the Wilkinson ADC section for performing the leading edge charge measurement. The information contained in the Wilkinson output pulse, namely the leading edge timing and the pulse width encoded signal charge, will be read and converted to digital data by a TDC. The Wilkinson cell operates under the control of a Gate Generator which consists of all differential logic cells. It is thus highly immune to substrate coupling and can operate in real time without disturbing the analog signals. The final output is then sent to the LVDS cell and converted to external low level differential signals. The main purpose of the Wilkinson ADC is to provide data which can be used for the correction of time-slew effects due to pulse amplitude variations. Time slewing correction improves the spatial resolution of the tracking detector. In addition, this type of charge measurement provides a useful tool for chamber performance diagnostics and monitoring (gas gain, ageing etc.). Further applications such as dE/dx measurements of slow moving heavy particles like heavy muon SUSY partners etc are conceivable. Test results on the conversion characteristics as well as measurements of noise performance respectively non-systematic charge measurement errors of the Wilkinson ADC are shown. The feasibility of the MDT system to perform particle identification through dE/dX measurement using the Wilkinson ADC is evaluated and results of a simulation study on energy separation probability is presented. It was found advantageous to be able to control or tune certain analog and functional parameters of the MDT-ASD, both at power-up/reset and during run time. A serial I/O data interface using a JTAG type protocol plus a number of associated DACs were implemented in the chip. In order to facilitate prototype testing during the design phase as well as to perform system calibration and test runs with the final assembly, a calibration/test pulse injection system was integrated in the chip. It consists of a bank of 8 parallel switched capacitors per channel and an associated channel mask register. The mask register allows for each channel to be selected separately whether or not it will receive test pulses. The capacitors are charged with external standard LVDS voltage pulses, yielding an input signal charge range similar to the expected range of the tube signals. This pulse injection system allows for automated timing and charge conversion calibration of the system. Hence, in principle all systematic errors of the readout electronics can be calibrated out for each individual channel. As a final point, an outlook to volume-production and production testing of the chip is given. Subject: Forwarded mail.... Date: Fri, 27 Apr 2001 18:37:26 +0200 (MEST) From: HU Christine To: Catherine.Decosse@cern.ch CC: Jean-Robert.Lutz@IReS.in2p3.fr, berst@lepsi.in2p3.fr, brogna@lepsi.in2p3.fr, colledan@lepsi.in2p3.fr, deptuch@lepsi.in2p3.fr, christine.hu@IReS.in2p3.fr Dear Catherine, Please find here after our paper fot the 7th workshop on Electronics for LHC experiments. Christine HU ============================================================================ ABSTRACT -------- The HAL25 is a mixed low noise, low power consumption and radtol ASIC intended for read-out of Silicon Strip Detectors (SSD) in the ALICE tracker. It is designed in a 0.25 micron CMOS process and is similar in concept to the previous chip ALICE128C. The chip contains 128 channels of preamplifier, shaper and a capacitor to store the charge collected on a detector strip. The analogue data is held by an external logic signal and can be serially read out through an analogue multiplexer. A slow control mechanism based on JTAG protocol was implemented for a programmable bias generator, an internal calibration system and selection of functional modes. SUMMARY ======= The HAL25 chip is a mixed analogue-digital ASIC designed for read-out of Silicon Strip Detectors (SSD) in the ALICE tracker. It is based on the ALICE first generation chip ALICE128C which was tested with good performance for an irradiation up to 50 krad. ALICE128C is now used in the SSD frontend electronic of the STAR tracker. For the ALICE experiment, a new radiation hardened circuit design was required to meet the total dose radiation and latchup background. It has been demonstrated that commercial deep submicron CMOS technologies exhibit intrinsic radiation tolerance. HAL25 has been designed with special design technics in a 0.25 micron CMOS process which is expected to meet the demands of low noise, low power consumption and radiation hardness required by the ALICE experiment. HAL25 contains 128 channels of preamplifier, shaper and a capacitor to store the charge collected on a detector strip. The data is held by an external logic signal and can be serially read out through an analogue multiplexer at 10 MHz. The chip is programmable by the JTAG protocol which allows: - to set up an adjustable bias generator which tunes the performances of analogue chains; - to choose the internal calibration system which sends a calibrated pulse to the inputs of selected chains; - to perform boundary scan. For the SSD layers, the ALICE experiment needs a readout circuit having very large dynamic range (+/-15 Mips) with good linearity and an adjustable shaping time from 1.4 us to 2.0 us. This is a challenge for such a circuit designed in a deep submicron process operated at only 2.5 V which is the edge of the use of standard analog design techniques. This paper will explain how the required specifications have been met: - single power supply; - low noise; - low power consumption (mean power consumption of designed circuit for a readout cycle of 1 ms is around 300 uW/ch); - large dynamic input range (+/-15 Mips) with good linearity; - differential current output to improve EMC; - geometry adapted to Tape Automated Bonding. The authors also expect to present evaluations of the circuit which was submitted to foundry at the end of March. Subject: LEB abstract Date: Fri, 27 Apr 2001 18:56:59 +0200 From: "Paul Aspell" Organization: CERN To: Hi Catherine, How are you ? How are the studies going ? I'm just finishing my thesis now so not too long to go before I finish. Then just nothing, can't wait. By the way, I plan to go to the LEB this year. Attached is an abstract. Cheers Paul Name: LEB.doc LEB.doc Type: Microsoft Word Document (application/msword) Encoding: base64 Download Status: Not downloaded with message Subject: LEB2001 abstract submission Date: Fri, 27 Apr 2001 19:41:21 +0200 From: franco gonella To: Catherine.Decosse@cern.ch, franco.gonella@pd.infn.it 1.Corresponding author Name: Franco Gonella Institution: Istituto Nazionale di Fisica Nucleare - Sez. Padova (Italy) Email address: fgonella@pd.infn.it Postal address: Via Marzolo, 8 - 35131 Padova (Italy) 2.Paper category LHC Experiment: CMS LHC Experiment Subsystem: MU LEB2001 Workshop topic: Electronics for muon detectors 3.Paper information Title: "The MAD", a Full Custom ASIC for the CMS Barrel Muon Chambers Front End Electronics Authors list with Institutions: Franco Gonella and Matteo Pegoraro from INFN - Sez. Padova (Italy) Summary: The analog frontend electronics for the muon chambers of CMS barrel has been integrated in a full custom ASIC, named "The MAD", developed by INFN Padova using 0.8 µm BiCMOS technology from Austria Mikro Systeme. Each chip provides the signal processing for 4 drift tubes in a 2.5x2.5mm2 die housed in a TQFP44 package. The 4 identical analog chains contained in the ASIC are made of a charge preamplifier followed by a simple shaper with baseline restorer, whose output is compared against an external threshold by a latched discriminator; the output pulses are then stretched by a programmable one shot and sent to an output stage able to drive long twisted pair cables with LVDS compatible levels. The working conditions of the detector set requirements for high sensitivity and speed combined with low noise and little power consumption. Moreover, as the basic requirement for the frontend is the ability to work at very low threshold to improve efficiency and time resolution, a good uniformity between channels of different chips is needed for sensitivity and threshold. Gain value is 3.3 mV/fC in average, constant up to 500 fC input with less than 1% integral nonlinearity; saturation occurs at about 800 fC. Threshold uniformity is very good, the r.m.s. is below 0.6 mV and the propagation delay is about 4 ns for signals above 30fC. Key characteristics for low threshold operation are noise and crosstalk: bare chips exhibit ENC ??1400 e- (slope of 60 e-/pF) and a value below 0.1% for the latter. Once mounted on the PCB these two figures increase to 1900 e- and 0.2% mainly because of the input protection network necessary to prevent HV discharge events. The power dissipation of the chip is very low, about 25 mW/channel so reducing the need for heat removal. Control and monitoring features have been included in the chip: to mask noisy wires each channel can be disabled at the shaper input resulting in little crosstalk to neighbors. It's also possible to check trigger functionality using a fast disable/enable feature, controlled via LVDS levels, acting on the output driver of left and right channel pairs. An absolute temperature probe with a sensitivity of 7.5 mV/(K has been integrated in order to detect electronics failures and monitor environmental changes. Two separate power supplies (5V and 2.5V) are used in order to reduce power drain and minimize interference between input and output sections. The routing has been particularly cured for power, digital ground and analog ground and many pins have been reserved for this purpose. Reliability is a critical point in a hardly accessible environment as CMS detector: tests performed (accelerated ageing and irradiation with neutrons, heavy ions and gamma rays) show good MTBF characteristics, low SEU rate and immunity to latch-up events in spite of using a standard and not too expensive technology. Abstract: To meet frontend electronics needs of CMS barrel muon chambers a full custom ASIC, named "The MAD", has been first developed by INFN of Padova and then produced in over 50.000 pieces to equip the 180.000 drift tubes. The chip provides 4 identical chains of amplification, discrimination and cable driving circuitry; also it integrates a flexible channel enabling/disabling capability and a temperature probe for monitoring purposes. The ASIC has been deeply tested resulting in good performances; particularly, big effort was put in radiation (neutron, gamma rays and ions) and ageing tests to check behavior and reliability in LHC environment. --------------------------------------------------------------------- Many thanks and best regards, Franco Gonella. Subject: Paper for LEB2001 Date: Fri, 27 Apr 2001 20:00:48 +0200 From: Miguel Ullan To: Catherine.Decosse@cern.ch Dear Madam, Here is a contribution to LEB 2001. I attach the abstract and summary as ASCII files and also paste them below. The main author is Miguel Ullan (Miguel.Ullan@cnm.es) who belongs to the Santa Cruz Institute for Particle Physics (SCIPP) at the University of California at Santa Cruz (UCSC). Best regards, Miguel Ullan -------------------------------------------------------------------------------------- IONIZATION RADIATION TOLERANCE OF THE ATLAS TRACKER ELECTRONICS M. Ullan*, D. Dorfan*, T. Dubbs*, A. A. Grillo*, E. Spencer*, A. Seiden*, H. Spieler**, M. Gilchriese**, M. Lozano*** * Santa Cruz Institute for Particle Physics (SCIPP) University of California at Santa Cruz Santa Cruz, CA 95064 USA Phone: 1 831 459 3567 Fax: 1 831 459 5777 E-mail: ullan@scipp.ucsc.edu ** Lawrence Berkeley National Laboratory (LBNL) University of California at Berkeley Berkeley, California, USA *** Centro Nacional de Microelectrónica (CNM-CSIC) Barcelona, Spain Abstract Ionization damage has been investigated in the IC designed for the readout of the detectors in the Semiconductor Tracker (SCT) of the ATLAS experiment at the LHC, the ABCD chip. The technology used in the fabrication has been found to be free from Low Dose Rate Effects which facilitates the studies of the radiation hardness of the chips. Other experiments have been done on the individual transistors in order to study the effects of temperature and the annealing, and to get a better understanding and a quantitative information about these mechanisms. With all this information, the suitable irradiation experiments have been designed for the chips to obtain a better answer about the survivability of these chips in the real conditions. Summary The ABCD chip is the IC that has been designed for the readout of the silicon detectors of the ATLAS Semiconductor Tracker (SCT) at the LHC. It is fabricated on the DMILL technology, which is a BiCMOS process on an SOI substrate. This chip will have to be placed very close to the detectors and, therefore, inside the active area of the SCT. That means that it will have to endure the same level of radiation that the detectors themselves. Different experiments have been carried out to study the radiation hardness of this technology and the ABCD chip itself to that high level of radiation. The physical mechanisms that intervene in the damage produced on the analog part of these chips from ionization or non-ionization radiation are different and it is better to study them separately to have a good understanding of the problem. This study is presented here where the effects of ionization radiation have been analyzed for the DMILL technology and the ABCD chip, taking into account the total dose effects. A first study has been to check if the bipolar transistors of the DMILL technology suffer from Low Dose Rate Effects (LDRE) which would largely complicate the rest of radiation hardness studies. Different radiation experiments have been carried out up to a high enough total dose and at a very wide range of dose rates using individual transistors of the technology. The result has demonstrated that the DMILL technology does not suffer from total dose effects which facilitates the realization of other radiation hardness studies. This result has been confirmed by other irradiations up to the total dose of interest. Together with this study, the annealing of the damage produced on the transistors has been investigated in order to separate this effect from the LDRE. Other experiments have been carried out at different temperatures in order to obtain the sensitivity of the radiation damage of these chips to temperature. The tests structures have been irradiated up to the total dose of interest and at a wide range of temperatures from 10 to 110 ºC. The results demonstrate the presence of two opposite effects. One is the increase in the damage at higher temperatures, and the other is the increase in the annealing of that damage also for higher temperatures. This two effects result in a worst case temperature at which the transistors suffer the largest damage, being the damage smaller at higher or lower temperatures. Finally the ABCD chip has been irradiated up to the total dose and at a high dose rate in order to obtain the total ionization damage that will be produced to the chip in the real experiment. Given that it has been demonstrated that there are not LDRE on this technology this experiment can be done at a high dose rate and in a short period of time. The results demonstrate that the ABCD chip remain within specifications after the expected ionization damage has been produced. -------------------------------------------------------------------------------------- --------------------------------------------------------------------- abstract.txtName: abstract.txt Type: Plain Text (text/plain) Name: summary.txt summary.txt Type: Plain Text (text/plain) Encoding: quoted-printable --------------------------------------------------------------------- ------------------------------------------------------------------------------------------- Miguel Ullán Comes Centro Nacional de Microelectrónica (CNM-IMB) Consejo Superior de Investigaciones Científicas (CSIC) Campus UAB, Bellaterra, Cerdanyola 08193 Barcelona Spain Tf: + 34 93 594 7700 Fax: + 34 93 580 1496 e-mail: Miguel.Ullan@cnm.es http://www.cnm.es ------------------------------------------------------------------------------------------- Subject: Abstract_summary_for_7th WORKSHOP_Sweden Date: Fri, 27 Apr 2001 14:29:12 -0500 (CDT) From: teren@fn781a.fnal.gov (Nikolai Terentiev) To: Catherine.Decosse@cern.ch CC: bondar@fnal.gov, ferguson@cmuhep2.phys.cmu.edu Dear Ms. Decosse. Please find below the abstract and summary of my talk proposed for the 7th Workshop on Electronics for LHC Experiments, Stockholm, Sweden, 10-14 September 2001. Thank you. Sincerely, Nikolai Terentiev (teren@fnal.gov) Carnegie Mellon University, Pittsburgh, PA, 15213, USA --------------------------------------------------------------------------- 1. Abstract Results of Radiation Tests on the Anode Front-end Electronics for the CMS Endcap Muon Cathode Strip Chambers T.Ferguson, N.Terentiev (Carnegie Mellon University, Pittsburgh, PA, 15213, USA) N.Bondar, A.Golyash, V.Sedov (Petersburg Nuclear Physics Institute, Gatchina, 188350, Russia) 7th Workshop on Electronics for LHC Experiments 10-14 September 2001, Stockholm, Sweden Abstract We report the results of several radiation tests on pre-production samples of the anode front-end electronics boards for the CMS endcap muon system. The crucial component tested was the 16-channel preamplifier ASIC (BiCMOS). The boards were exposed to doses up to 80 krad in a 63 MeV proton beam, and to a neutron fluence up to 2*10**12 n/cm**2 from a nuclear reactor. The static (current and voltage) and dynamic (noise,threshold, gain and timing) characteristics were measured versus the radiation dose. ---------------------------------------------------------------------------- 2. Summary Results of Radiation Tests of the Anode Front-end Electronics for the CMS Endcap Muon Cathode Strip Chambers T.Ferguson, N.Terentiev (Carnegie Mellon University, Pittsburgh, PA, 15213, USA) N.Bondar, A.Golyash, V.Sedov (Petersburg Nuclear Physics Institute, Gatchina, 188350, Russia) 7th Workshop on Electronics for LHC Experiments 10-14 September 2001, Stockholm, Sweden Summary The peak luminosity of LHC, 10**34 cm**-2*sec**-1, combined with the 7 TeV beam energy, will create a very hostile radiation environment in the detector experimental halls. Radiation tolerance and reliability are important issues for the CMS electronics, including the endcap muon CSC front-end electronics. The most severe conditions in the muon endcap region are in the vicinity of the ME1/1 CSC chambers. Here, the neutron fluence and the total ionizing dose (TID) accumulated during 10 years of LHC operation are expected to be about 6-7*10**11n/cm**2 (at En>100 keV) and 1.8-2 krad, respectively (Ref.1). The goal of our measurements was to test the performance of the anode front-end boards, with specially designed preamplifier chips (AMI 1.5 micron BiCMOS technology) on them, up to a level of 3 times these doses, and to observe the presence of single-event effects such as latch-up, at higher doses (Ref.2). The boards were irradiated in a 63 MeV proton beam and received a TID up to 14 and 80 krad. No latch-ups or spikes or any changes in the static parameters (amplifier, discriminator and regulator voltages) were observed. However, the dynamic parameters such as threshold, gain and slewing time were sensitive to the radiation, showing a maximum deviation of 40% (for slewing time) at a TID of 60 krad. The noise and the resolution time were not affected at all. At the required 3 times level of TID (5-6 krad), all changes were practically negligible. The corresponding graphs will be presented. Some boards were exposed to a reactor neutron fluence up to 2*10**12 n/cm**2, at a neutron energy of 100 keV < En < 10 MeV. They also received a TID of about 50-60 krad from gammas which accompanied the reactor neutrons. About 50% of the boards survived, showing moderate changes (20-30%) in dynamic characteristics in a test taken one month after the irradiation. The rest of the boards recovered after one week of heating at 110 degrees C. Further heating returned all the parameters for all boards to the norm. From our results we can roughly estimate that, for the test doses given above, the annealing time is about a few months at room temperatures. Since the LHC rate of real radiation exposure is much slower than this, we conclude that the anode front end boards should not show any radiation damage during normal LHC operation. We are thankful to M. Tripathi and B. Holbrook of the University of California, Davis, and to T.Y. Ling and B. Bylsma of the Ohio State University for their valuable help. References: 1. "A global radiation test plan for CMS electronics in HCAL,Muons and Experimental Hall". http://cmsdoc.cern.ch/~faccio/ 2. T.Y.Ling. "Radiation tests for EMU electronics". http://www.physics.ohio-state.edu/~ling/elec/rad_emu_proc.pdf Subject: leb2001 (fwd) Date: Fri, 27 Apr 2001 20:51:47 +0100 From: Marco Dallavalle To: Catherine.Decosse@cern.ch Dear Catherine, please find enclosed an abstract for LEB2001. Best regards, Marco Dallavalle ------------------------------------------------------------------- ------------------------------------------------------------------- Abstract and Summary for submission to LEB2001 in Stockholm April 30, 2001 TITLE Use of antifuse-FPGAs in the Track-Sorter- Master of the CMS Drift Tube Chambers AUTHORS G.M.Dallavalle, A.Montanari, F.Odorici, G.Torromeo, R.Travaglini, M.Zuffa INFN and University, Bologna, Italy Abstract The Track-Sorter-Master (TSM) is an element of the on-chamber trigger electronics of a Muon Barrel Drift Tube Chamber in the CMS detector. The TSM provides the chamber trigger output and access to the trigger electronic devices for monitoring and configuration. The specific robustness requirements on the TSM are met with a partitioned architecture based on antifuse-FPGAs. These have been successfully tested with a 60 MeV proton beam: SEE and TID measurements are reported. Summary Drift Tubes Chambers (DTCs) are used to detect muons in the barrel of the Compact Muon Solenoid (CMS), which will collect data at the future Large Hadron Collider (LHC) of CERN. In LHC, two proton beams of 7 TeV will collide at a bunch crossing frequency of 40 MHz. Electronic devices installed on the DTCs analyse every bunch crossing, with no deadtime, and search for possible muon track segments. In particular, the Trigger Server system (TS) examines the search results from smaller sections of a DTC, rejects fakes and duplicates, and selects the best two segments overall, thus reducing the chamber output by a factor of 25. Because of the limited accessibility of front-end electronics and the high neutron flux expected in the CMS cavern, priority in the TS design is given to partitioning and to remote control and testability. The TS architecture is a compromise between optimal partitioning, for minimising the impact of failures, and minimal trigger latency, in order to limit event data buffering. In the TS, muon track segment selection is performed in two steps: Track Sorter Slave (TSS) units (each serving 1/7 of a DTC) in the first layer feed Track Sorter Master (TSM) units (one each DTC) in the second layer. For the TSS, we designed a 0.5 micron CMOS ASIC implementing an ad-hoc fast sorting algorithm. Overall, in the CMS muon barrel about 1300 TSS ASICs will perform as a single synchronous system. The TSM does the final selection and provides access to the TSSs for monitoring and configuring. The TSM is partitioned in several distinct blocks with partial redundant functionality, and automatic failure detection and re-configuring. For manufacturing the TSM blocks, antifuse-FPGAs, which have permanent configuration once programmed, are chosen, after their radiation tolerance has been successfully tested for use in LHC. Single Event Effect and Total Irradiation Dose measurements for the Actel A54SX antifuse-FPGAs were performed using a 60 MeV proton beam. The chips show good tolerance to high radiation doses of 10 to 70 Krads. For Single-Event-Upsets, we set an upper- limit cross-section of 2.9/10^12 cm2 (90% c.l.) per chip. Subject: Abstract from Peter Alfke, Xilinx Date: Fri, 27 Apr 2001 13:51:23 -0700 From: "Peter Alfke" Organization: Xilinx To: Catherine.Decosse@cern.ch Here is my abstract. I will e-mail the summary early next week. I saw that you allocated 45 minutes for my talk. I have plenty of subjects to talk about. Thanks for inviting me. Greetings Peter Alfke Evolution, Revolution, and Convolution Recent Progress in Field-Programmable Logic by Peter Alfke Xilinx, Inc. Evolution: Bigger, faster, cheaper chips, better software. Revolution: Versatile I/O for 5 V, 3.3 V, 2.5 V and 1.8 V interfaces Controlled-impedance I/O drives transmission lines, simplifies pc-boards Versatile clock management eliminates delay, adjusts phase Dedicated fast multipliers (>100 per chip) PowerPC cores, up to 4 per chip 3.125 Bbps ( 2.5 Gbps data ) serial interface, clock recovery, 8B/10B, 20-bit FIFOs ( 10 Mbps in the future ) Convolution: Using BlockRAM as state machines Using multipliers as logic or arithmetic shifters Using input flip-flops to count at 1 GHz Using FPGAs with asynchronous clocks Using triple redundancy to correct single-event upsets Subject: Abstract submission for LEB 2001 Date: Sat, 28 Apr 2001 11:48:08 +0200 (MET DST) From: Gianni Mazza To: catherine.decosse@cern.ch Dear Catherine, here are my abstract and summary for the LEB 2001. Best regards Gianni Giovanni Mazza Lab. di Elettronica INFN Sez. Torino Via P. Giuria 1 10125 Torino - Italy Tel. +39 011-6707380 Fax +39 011-6699579 E-mail mazza@to.infn.it --------------------------------------------------------------------- Title : New building blocks for the ALICE SDD readout and Detector Control System in a commercial 0.25 um CMOS technology with radiation tolerant layout techniques. Authors : G.Mazza[INFNTo], M.Idzik[INFNTo], A.Rivetti[UniTo], F.Rotondo[INFNTo] Institutes : [INFNTo] INFN sezione di Torino, Italy [UniTo] Universita` di Torino, Italy --------------------------------------------------------------------- New building blocks have been developed for the electronic readout of the ALICE Silicon Drift Detector. Those blocks include a 10 bit A/D converter with a reduced input capacitance, an 8 bit D/A converter based on the current mirror scheme, a voltage regulator and biasing schemes. The blocks will be used in the PASCAL chip to improve the performances of the existing prototype and will be the building blocks for the SDD Detector Control System ASIC. The circuits have been developed in a commercial CMOS 0.25 um technology using radiation tolerant layout techniques. --------------------------------------------------------------------- The front-end prototypes for the electronic readout of the ALICE experiment Silicon Drift Detector have been designed and succesfully tested. Nevertheless, a number of system requirements as minimize dead time, avoid external biasing and develop the Detector Control System have to be addressed. At this purpose, new building blocks have been developed. These blocks include a 10 bit A/D converter, an 8 bit D/A converter based on the current mirror scheme, a voltage regulator and biasing schemes. The A/D converter is based on the successive approximation principle. In order to reduce the input capacitance, the internal DAC has been splitted into a 5 bit main DAC and a 5 bit sub DAC. This arrangement makes possible to reduce the input capacitance of a factor of 8 compared to the previous version. The D/A converter is based on a matrix of 256 current mirrors. This technique relaxes the matching requirements and therefore improves DNL and INL. A transimpedance amplifier has been designed in order to convert the output current into a voltage. The voltage regulator and bias circuits will be integrated in the final front-end ASIC ( named PASCAL ) in order to have no external analog signals in the front-end board. Those components will be also the building blocks for the Detector Control System ASIC which will be located on both ends of the SDD ladder. The circuits have been developed in a commercial CMOS 0.25 um technology using radiation tolerant layout techniques. Subject: Re: 7th Workshop Summaries Date: Sat, 28 Apr 2001 14:24:09 +0400 From: "Ñêîðîáîãàòîâ Ï.Ê." To: "Catherine Decosse" Dear Catherine! Let me to send you two my summaries for 7th LHC Workshop. 1. Influence of Temperature on Pulsed Focused Laser Beam Testing P.K.Skorobogatov, A.Y.Nikiforov 2. The Behavior of P-I-N Diode under High Intense Laser Irradiation P.K.Skorobogatov, A.S.Artamonov, B.A.Ahabaev My address Skorobogatov Peter K., Kashirskoe shosse, 31, 115409 Moscow, Russia Fax: (095) 324-04-20 Note: our Fax is combined with voice telephone. So, please say "Receive a fax " and it will be turn on as a Fax. E-mail pkskor@spels.ru Best wishes, Peter K. Skorobogatov Influence of Temperature on Pulsed Focused Laser Beam Testing P.K.Skorobogatov, A.Y.Nikiforov Specialized Electronic Systems, Kashirskoe shosse, 31, 115409, Moscow, Russia pkskor@spels.ru Abstract Temperature dependence of p-n junction radiation-induced charge collection under 1.06 and 0.53 micrometer focused laser beams was investigated in the temperature range from 22 to 110 C using experiments and numerical simulation. It was shown that in the case of 0.53 micrometer laser irradiation the temperature practically does not affect the collected charge. In the case of 1.06 micrometer laser irradiation the theory and experiments have shown the essential growth (from 2 to 3 times) of collected charge with temperature. The result obtained must be taken into account in device SEE selection for LHC electronic. Summary The high radiation environment of the LHC experiments requires the electronics to withstand single event effects (SEE). The procedure for estimating of integrated circuits SEE vulnerability based on particle accelerators testing is very expensive. The focused laser sources may be used for SEE investigation and estimation [1,2]. Laser simulation of SEE is based on the focused laser beam capability to induce local ionization of IC structures. A wide range of particle linear energy transfer (LET) and penetration depths may be simulated varying the laser beam spot diameter and wavelength. The temperature dependence of the laser absorption coefficient in semiconductor affects the equivalent LET and must be accounted for when devices are tested at temperature range [3]. In order to estimate the influence of temperature on SEE laser testing parameters we have analyzed the temperature dependence of charge collected by test structure p-n junction. The experiments were performed using the original "PICO-2E" pulsed solid-state laser simulator in basic (1.06 micrometer) and frequency-double (0.53 micrometer) modes with laser spot diameter of 5 micrometers. The numerical simulations were performed using the original "DIODE-2D" 2D software simulator. The investigated test structure was manufactured in a conventional 2 micrometer bulk CMOS process and includes well-substrate p-n junction. The measurements of p-n junction collected charge were performed in the temperature range from 22 to 110 ?C for two laser beam spot positions: within the n-well and out of junction area. It was shown that in the case of 0.53 micrometer laser irradiation the temperature practically does not affect the collected charge because of slight laser absorption coefficient temperature dependence in this range. The theoretically predicted variations of collected charge do not exceed 10% and may be explained by carrier lifetime and mobility temperature dependences. In the case of 1.06 micrometer laser irradiation the theory and experiment have shown the essential growth of collected charge with temperature. It is corresponds with strong laser absorption coefficient temperature dependence for photon energy near the bandgap. The theoretical prediction gives the approximately doubling of collected charge in the range from 22 to 110 C. The experimental results show that SEE sensitivity increases at least three times in this temperature range. The difference between measured and simulated results may be explained by uncertainties of laser absorption coefficient temperature dependence near the edge of silicon fundamental band-to-band absorption zone. The results obtained prove that the temperature dependence of the laser absorption coefficient in semiconductor affects the equivalent LET and must be taken into account in device SEE selection for LHC electronic. References [1] C.F.Gosset, B.W. Hughlock, A.H.Johnston, "Laser simulation of single particle effects", IEEE Trans. Nucl. Sci., vol. 37, no.6, pp. 1825-1831, Dec. 1990. [2] J.S. Melinger, S. Buchner, D. McMorrow, W.J. Stapor, T.R Wetherford, A.B. Campbell and H. Eisen, "Critical evaluation of the pulsed laser method for single-event effects testing and fundamental studies", IEEE Trans. Nucl. Sci., vol. 41, no.6, pp. 2574-2584, Dec. 1994. [3] A.H. Johnston, "Charge generation and collection in p-n junctions excited with pulsed infrared lasers", IEEE Trans. Nucl. Sci., vol. 40, no. 6, pp. 1694 - 1702, Dec. 1993. The Behavior of P-I-N Diode under High Intense Laser Irradiation P.K.Skorobogatov, A.S.Artamonov, B.A.Ahabaev Specialized Electronic Systems, Kashirskoe shosse, 31, 115409, Moscow, Russia pkskor@spels.ru Abstract The dependence of p-i-n diode ionizing current amplitude vs 1.06 micrometer pulsed laser irradiation intensity is investigated. It is shown that analyzed dependence becomes nonlinear beginning with rela- tively low laser intensities near 10 W/cm2. This effect is connected with the modulation of pi-n diode intrinsic region by laser irradiati- on. As a result the distribution of electric field becomes non-uniform that leads to decrease of excess carriers collection. The ionizing current pulse form becomes more prolonged and does not repeat the la- ser pulse waveform. It is necessary to take into account when p-i-n diode is used as a laser intensity dosimeter. Summary Pulsed laser sources are widely used for dose rate effects simu- lation in IC's. The Nd:YAG laser with 1.06 micrometer wavelength is near ideal for silicon devices, with a penetration depth near 700 mic- rometers. The measurements of pulsed laser irradiation intensity and waveform monitoring may be provided with p-i-n diode. High electric field in its intrinsic region provides the full and fast excess carri- ers collection. As a result the ionizing current pulse waveform repe- ats the laser pulse within the accuracy of several nanoseconds. Possible nonlinear ionization effects may disturb the behavior of p-i-n diode at high laser intensities. To investigate the p-i-n diode possibilities at high laser intensities the original software simula- tor "DIODE-2D" and the pulsed laser simulator with 1.06 micrometer wa- velength were used. The typical p-i-n diode with 380 micrometers int- rinsic region width under 300 V reverse bias was investigated. The si- mulation of p-i-n diode structure have shown that linear dependence between laser intensity and ionizing current is valid only at relati- vely low intensities up to 10 W/cm2 under 11 ns laser pulse irradiati- on. The ionization distribution nonuniformity connected with laser ra- diation attenuation does not affect the dependence because of relati- vely low excess carrier density to sufficiently change the absorption coefficient. In the field of high laser intensities this dependence becomes non-linear and ionizing current increases more slowly than la- ser intensity. The numerical results were confirmed by experimental measurement of pi-n diode ionizing reaction in a wide range of laser intensities. The pulsed laser simulator "RADON-5E" with 1.06 microme- ter wavelength and 11 ns pulse width was used in the experiments as a radiation source [1]. The laser pulse maximum intensity was varied from 0.3 up to 2ú103 W/cm2 with laser spot size covering the entire chip. It provides in silicon the equivalent dose rates up to 109 rad(Si)/s As in the case of gamma irradiation [2], the reason of non-linea- rity is connected with the modulation of p-i-n diode intrinsic region by excess carriers. Because of low level of initial carriers concent- ration the modulation takes place at relatively low laser intensities. As a result of modulation the distribution of electric field in the intrinsic region becomes non-uniform that leads to decrease of excess carriers collection. The behavior of p-i-n diode becomes similar to that of ordinary p-n junction with prompt and delayed components of ionizing current. The prompt component repeats the dose rate waveform. The delayed component is connected with the excess carriers collection from regions with low electric fields. As a result the ionizing cur- rent pulse form becomes more prolonged and dose not repeat the laser pulse waveform. The non-linear character of behavior and prolonged reaction must be taken into account when p-i-n diode is used as a laser intensity dosimeter in LHC experiment. References [1]. "RADON-5E" Portable Pulsed Laser Simulator: Description, Qu- alification Technique and Results, Dosimetry Procedure/A.Y. Nikiforov, O.B. Mavritsky, P.K. Skorobogatov et all//1996 IEEE Radiation Effects Data Workshop. P. 49-54. [2]. P.K.Skorobogatov, A.S.Artamonov, B.A.Ahabaev The Nonlinear Behavior of P-I-N Diode in High Intense Radiation Fields// Proceedings of the Sixth Workshop on Electronics for LHC Experiments. Krakow, Sep- tember 22-26, 2000. P. 499 - 501. Subject: Abstract and summary for LEB2001 Date: Sat, 28 Apr 2001 20:52:20 +0200 From: András Fenyvesi Organization: ATOMKI, Debrecen, Hungary To: Catherine.Decosse@cern.ch Dear Ms. Decosse, Please, find the attached ASCII file for the LEB2001 conference. Yours sincerely, Andras Fenyvesi --------------------------------------------------------------------- Neutron radiation tolerance tests of optical and opto-electronic components for the CMS Muon Barrel Alignment L. Baksay, P. Raics, Zs. Szabó, L. Molnár, G. Pszota Institute of Experimental Physics, Debrecen University, Debrecen, Hungary A. Fenyvesi, J. Molnár, Institute of Nuclear Research (ATOMKI), Debrecen, Hungary Gy. L. Bencze Institute of Particle and Nuclear Physics, Budapest, Hungary CERN, Geneva, Switzerland L. Brunel CERN, Geneva, Switzerland Institute of Experimental Physics, Debrecen University, Debrecen, Hungary Abstract Components (LED light sources, LED driver and controller electronics, lens and video-sensor) of the barrel muon position monitoring system of the LHC CMS experiment have been irradiated with p(17.5 MeV)+Be neutrons. The tests were performed at the MGC-20E cyclotron of ATOMKI (Debrecen, Hungary). The neutron fluences delivered to the components were 2.6E+12 n/cm2 and 8.0E+13 n/cm2 (the expected values for the Barrel Muon and ME1/1 chambers, respectively). Changes of the electrical and optical characteristics were investigated. This work was supported by the Hungarian National Research Fund (OTKA). Contract Nos.: T026184 and T026178. Summary Performance of the muon detecting system of the CMS detector of the Large Hadron Collider (LHC) is affected by the position and orientation of the individual chambers. In the case of the barrel muon detectors, their alignment will be controlled on the basis of the information that is provided by the position monitoring system. This system will consist of LED light sources, LED driver and controller electronics, optical lenses and video-sensors. They will have to work in a radiation environment, where the highest expected flux of the neutron component is about 1.0E+03 n/cm2/sec, and the estimated time of operation is 5.0E+10 sec. The total expected neutron flux is 2.6E+12 n/cm2 and 8.0E+13 n/cm2 for the Barrel Muon and ME1/1 chambers, respectively. Radiation damage induced by neutrons can alter electrical and optical characteristics of the components and thus the accuracy of the whole barrel muon position monitoring system. Neutron radiation hardness tests of the components to be used in the Barrel Muon Alignment System were carried out using the broad-spectrum p(17.5 MeV)+Be neutron source ( 0 < En < 18 MeV, < En> = 3.7 MeV) of ATOMKI (Debrecen, Hungary). Low current high intensity point-like LED light sources emitting at 660 nm (Type: FH1011, Stanley Electric Co. Ltd.) were irradiated up to 2.6E+12 n/cm2. Three modes of operation were studied: a) voltage on permanently, b) voltage off permanently and c) voltage on for 1 sec and off for 19 sec. For all of these modes of operation, the light yield decreased almost linearly as a function of the neutron fluency and approximately 50 % decrease was observed at the end of the irradiations. No other change in the electrical and spectral characteristics was measurable. LED current driver and controller electronics with Microchip PIC16F84 processors were irradiated up to 8.0E+13 n/cm2. Some 20 % loss of the output currents of the LED controllers was observed at the end of the irradiation. The degradation of the current drivers was negligible below 1.0E+11 n/cm2 (the expected fluency at the position of operation of the device). Two processors were studied. Both damaged only after delivering ~ 2.0E+13 n/cm2 neutron fluency to them as the dramatically increased current consumption of the electronics indicated. Plano-convex single lenses were irradiated up to 8.0E+13 n/cm2. They were made of BK7 glass without coating and their diameter was 10 mm. No measurable change of the spectral transmission and the refraction (focal length) was observed. VM5402 video cameras with VV5402 CMOS sensor device (VLSI Vision Ltd.)were irradiated up to 2.8E+12 n/cm2. The radiation damage of the sensor resulted in the altered nearly Gaussian distribution of the light sensitivity of the individual pixels in all modes of operation. The mean values decreased while the sigma values increased in all three modes ( a) voltage on permanently, b) voltage off permanently and c) voltage on for 1 sec and off for 19 sec). Apart from the general sensitivity loss, the spectral sensitivity of the sensor did not change. --------------------------------------------------------------------- Andras Fenyvesi PhD Institute of Nuclear Research of the Hungarian Academy of Sciences Cyclotron Dept. Andras Fenyvesi PhD Institute of Nuclear Research of the Hungarian Academy of Sciences Cyclotron Dept. Bem ter 18/c., P. O. Box 51 Fax: 36-52-416181 Debrecen Work: ATOMKI, Debrecen, Hungary H-4001 Hungary Additional Information: Last Name Fenyvesi First Name Andras Version 2.1 Subject: Re: call for paper LECC2001 Date: Sun, 29 Apr 2001 19:47:23 +0400 From: Leonid Efimov Organization: JINR , Dubna , Russia To: Catherine DECOSSE CC: Vito.Lenti@cern.ch, orlandov@mail.cern.ch Dear Catherine, herewith I send you an application to present A PROTOTYPE FAST MULTIPLICITY DISCRIMINATOR FOR ALICE L0 TRIGGER Leonid Efimov [1], Vito Lenti [2] and Orlando Villalobos-Baillie [3] --------------------------------- [1] JINR-Dubna, Russia [2] INFN-Bari, Italy [3] University of Birmingham, UK An approval needed from the ALICE collaboration is going to be O'K. Leonid Efimov should be fixed as a reporter actually, but, in the case of insoluble drawbacks, Vito Lenti would be able instead. Kind regards Leonid --------------------------------------------------------------------- A PROTOTYPE FAST MULIPLICITY DISCRIMINATOR FOR ALICE L0 TRIGGER Leonid Efimov, Vito Lenti and Orlando Villalobos-Baillie Abstract ******** The design details and test results of a prototype Mutiplicity Discriminator (MD) for the ALICE L0 Trigger electronics are presented. The MD design is aimed at the earliest trigger decision founded on a fast multiplicity signal cut, in both options for the ALICE centrality detector: Micro Channel Plates or Cherenkov counters. The MD accepts detector signals with an amplitude range of plus-minus 2.5 V, base duration of 1.8 ns and rise time of 300-400 ps. The digitally controlled threshold settings give an accuracy better than 0.4% at the maximum amplitude of the accepted pulses. The MD internal latency of 15 ns allows for a decision every LHC bunch crossing period, even for the 40 MHz of p-p collisions. --------------------------------------------------------------------- A PROTOTYPE MULTIPLICITY DISCRIMINATOR FOR ALICE L0 TRIGGER Leonid Efimov, Vito Lenti and Orlando Villalobos-Baillie Summary ******* A functional scheme and other considerations for the Prototype Multiplicity Discriminator (MD), as an element of ALICE L0 Trigger Front-End Electronics (FEE), are given for the proposed MCP-based detector option. The MD has to produce a Pre-Trigger on Multiplicity by cut of a fast linear sum of 8 signals from pads belonging to an MCP disc sector. This is foreseen within every FEE card according to programmable threshold codes delivered by a Source Interface Unit through the ALICE Detector Data Link. The prototype MD schematics and implementation are described in details around a functional scheme and a schematic view of the input analog section. The approach used in the design was to implement a leading edge discriminator by a proper combination of an ultra-fast voltage comparators and a digital-to- analog converter (DAC) from Analog Devices. The shaper, built on components of Motorola MECL 10KH logic series, provides the output signal with a correct form, duration and 16 mA for 50 Ohm load. The prototype MD board is mounted in a double-width NIM module to support conventional test facilities. The correlation between MD preset and real (effective) thresholds has been studied in order to evaluate the MD sensitivity to very fast and low-amplitude detector signals. Some results of such measurements, using a fast programmable pulse generator, are shown as the effective voltage threshold versus the DAC threshold values. Next calculation of the equivalent electric charge, carried by these pulses, gave the rough estimates of the MD sensitivity as a minimum of over DAC threshold pulse charge needed to trigger the scheme. An estimate of a Prototype MD input capacity was obtained also. The first experimental test of the prototype MD was performed at CERN PS/T10 area with muon beams of 7.5 GeV/c. The aim of this experiment was two fold: a) to test the timing properties of the prototype MD; b) to simulate a study of multiplicity/centrality versus the MD threshold. Results from the MD, used instead of a specialized fast timing discriminator for time-of-flight measurements, are presented with a distribution of events versus the time-to-digital converter channels. A resolution of about 120 ps should be taken as a good one because the MD is not optimized for timing applications. In conclusions the main achievement is defined as a prototype amplitude discriminator, for the ALICE L0 multiplicity Trigger, has been designed, elaborated and tested to stand short nanosecond signals coming from the ALICE T0/Centrality detector on Micro Channel Plates base. Commercially available, inexpensive and fast components have been used to implement the prototype MD. It features an input signal range from 0 to plus-minus 2.5 V, a programmable threshold control with 8 bit resolution, and an output signal latency of 15 ns. The minimum input signal charge, needed to trigger the scheme over the DAC threshold, has been found in about 0.26 pC. While applying the MD for timing in MIPs time-of-flight measurements, a resolution of about 120 ps has been obtained. The MD was also tested by studying the response to real MCP signals as a function of the MD threshold. Subject: LEB paper Date: Mon, 30 Apr 2001 08:22:09 +0200 From: "Alessandro Marchioro" To: CC: "Paulo Moreira" , "Giovanni Cervelli" Dear Catherine, please find attached another contribution to the LEB conference. The corresponding author will be Giovanni Cervelli. Thank you for your attention. Best regards, Sandro Marchioro --------------------------------------------------------------------- Name: Cervelli_LEB_2001.doc Type: Microsoft Word Document Cervelli_LEB_2001.doc (application/msword) Encoding: base64 Download Status: Not downloaded with message Subject: LEB2001 Date: Mon, 30 Apr 2001 09:43:05 +0200 From: Jeroen VAN HUNEN Organization: CERN To: Catherine.Decosse@cern.ch CC: Giorgio Stefanini Dear Catherine, I include my abstract for the LEB workshop. I have not yet included a summary, since some of the measurements are still continuing. Let me know if it is alright to send a summary later. Thanks, Best regards, Jeroen Abstract: Irradiation Tests and Tracking Capabilities of the Alice1LHCb Pixel Chip J.J. van Hunen (For the ALICE collaboration) The Alice1LHCb front-end chip has been designed in a 0.25um CMOS commercial technology, with special design rules to obtain radiation tolerance, for the ALICE pixel and the LHCb RICH detectors. The chip has been irradiated with low energy protons and heavy ions, to determine the cross-section for Single Event Upsets, and with X-rays to evaluate the sensitivity to the Total Ionizing Dose. We report the results of those measurements. We also report preliminary results of measurements done with minimum ionising particles in a test beam at the CERN SPS. -------------------------------------------------- Jeroen J. van Hunen CERN, European Organization for Nuclear Research CH - 1211 Geneva 23 Switzerland Office : 160-1-012 Phone : 41-(0)22-7679961 GSM : 41-(0)79-2014785 Fax : 41-(0)22-7679480 -------------------------------------------------- Subject: LHC electronics workshop Date: Mon, 30 Apr 2001 10:55:39 +0200 (CEST) From: Ian Dawson To: Catherine.Decosse@cern.ch Hi, here is an abstract for a poster contribution to the LHC electronics workshop. Title ----- Activation studies for an ATLAS SCT module. Abstract -------- One of the consequences of the harsh radiation environments at LHC experiments will be induced-activation of detector systems. This has implications for operation and maintenance scenarios. We have simulated the radiation environment of the ATLAS SCT system and made first estimates on the levels of induced activation of an SCT module. This has included studying both neutron-induced and spallation-induced activation. Dose rates are also obtained and compared to other parts of the ATLAS detector where estimates have also been made. Authors ------- C.Buttar, I.Dawson, A.Moraes (University of Sheffield, UK) Subject: contribution to workshop Date: Mon, 30 Apr 2001 10:58:57 +0200 (MEST) From: Maria Teresa Brunetti To: catherine.decosse@cern.ch "Design and performance of a circuit for the analogue optical transmission in the CMS inner tracker" G. M. Bilei, M. T. Brunetti (corresponding author), F. Ceccotti, B. Checcucci, V. Postolache, A. Santocchia Abstract A new circuit for the conversion of analogue electrical signals into the corresponding optical ones has been built and tested by the CMS group of Perugia. This opto-hybrid circuit will be used in the read out electronics of the inner barrel part of the CMS tracker. The opto-hybrid is a vetronite circuit equipped with one programmable laser driver chip and up to 3 laser diodes, all being radiation tolerant. The description of the circuit and its performances are reported and discussed. Summary The opto-hybrid circuit is employed in the analogue optical link of the CMS inner barrel and converts the analogue electrical signal coming from silicon detectors and sampled by the APV chips into the analogue optical signal to be transmitted via optical fibres. The opto-hybrid is an FR4 (vetronite) circuit with dimensions of 30 x 22 mm2. The active devices are a programmable laser driver chip and up to 3 laser diodes (output channels). The laser driver through an I2C interface biases each laser diode in its linear response region. Analogue input signals up to +/- 300 mV from the MUX connected to the APV chips modulate the bias currents. The optical fibres escaping from each laser diode carry the analogue signal, which will be converted again, out of the beam area, into an electrical signal and is finally digitised for acquisition and analysis. For test purposes the opto-hybrid has been temporarily connected to ancillary circuits for power supply and signal injection. The test set-up includes an optical receiver, which converts the optical signal into the electrical output to be read by the scope or by the spectrum analyser. A set of routines, written in Labview 5.1, allows the remote control of the instruments and the automatic execution of the electrical tests. For a preliminary validation of the opto-hybrid circuits, the measurements to be performed are gain, integral-non-linearity, signal-to-noise ratio, crosstalk and bandwidth. The gain of the optical link is defined as the ratio between the output electrical signal and the corresponding pulse injected at the opto-hybrid input and is pre-settable through the programmable laser driver up to a value of 2.5. The gain test has shown a good agreement between the measurements and the values set via the laser driver. The integral-non-linearity (INL) test gives the deviation from a linear fit of the measured output values versus an increasing input voltage. The tested opto-hybrid chips have shown an INL estimated to be less than 3%, according to the request asked for its performances. The crosstalk is the noise measured on adjacent channels when one laser chip is pulsed. This test was affected by an impedance mismatch, which will be removed in further measurements, but the low noise values found were, nevertheless, encouraging. In order to completely characterise the opto-hybrid behaviour, thermal cycles and irradiation with particles are foreseen. All these tests will guarantee the correct operation of the opto-hybrid once in the hostile environment of the LHC tunnel. Subject: paper on SCT128A Date: Mon, 30 Apr 2001 11:54:26 +0200 (METDST) From: Wladyslaw Dabrowski To: Catherine DECOSSE Dear Catherine, Below is the summary of one paper. A second one is still on my list of things to be done .... hopefully the deadline is not very strict. And one more thing, I'm trying to stimulate my colleagues from the SCT to submit a paper on power supply and detector bias distribution in the SCT, something which would suit perfectly to one of the topics. On the other hand there won't be probably many papers on this subject. What could be a possible delay which would not make you too much trouble? Best regards, Wladek Dabrowski ********************************************************************* Title: Progress in Development of the Analogue Readout Chip for Si Strip Detector Modules for LHC Experiments Authors: E. Chesi, A. Clark, W. Dabrowski, D. Ferrere, J. Kaplon, C. Lacasta, J. Lozano, S. Roe, R. Szczygiel, P. Weilhammer, A. Zsenei. Abstract We present a new version of 128-channel analogue front-end chip SCT128A for readout of silicon strip detectors. Following the early prototype developed in the DMILL technology we have elaborated a design with the main goal to improve its robustness and radiation hardness. The improvements implemented in the new design are based on experience gained on the DMILL technology while developing the binary readout chip for the ATLAS Semiconductor Tracker. The architecture of the chip and critical design issues will be discussed. The performance of modules built of ATLAS baseline detectors read out by 6 SCT128A chips will be presented and discussed. Summary In parallel to development of the binary readout chip for the ATLAS Semiconductor Tracker we have been developing a chip with analogue readout architecture - SCT128A. Both chips have been developed in the DMILL technology and employed the same concept of a fast front-end circuit based on bipolar transistors. Analogue architecture has a number of potential advantages compared to the binary one. A feature, which is particularly important for large installations like trackers for LHC experiments, is immunity of this architecture to common noise effects. First prototype of the SCT128A chip was designed and manufactured in an early stage of stabilisation of the DMILL process. In the meantime the DMILL process has been improved and stabilised. The development of the ABCD binary readout chip helped us to understand better and quantify various aspects of the process like matching, parasitic couplings through the substrate and radiation effects. The conclusions from the work on the ABCD chip have been implemented in the new design of the SCT128A chip with a main goal to improve robustness and radiation hardness of the new chip. The SCT128A is designed to meet all basic requirements of a silicon strip tracker for LHC experiments. It comprises five basic blocks: front-end amplifiers, analogue pipeline (ADB), control logic including derandomizing FIFO, command decoder and output multiplexer. The front-end circuit is a fast transimpedance amplifier followed by an integrator, providing a semi-gaussian shaping with a peaking time of 20-25ns, and an output buffer. The peak values are sampled at 40 MHz rate and stored in the 128-cell deep analogue pipeline. Upon arrival of the trigger the analogue data from the corresponding time slot in the ADB are sampled in the buffer and sent out through the analogue multiplexer. The gain of the front-end amplifier is of about 50mV/fC. The designed peaking time for the nominal values of resistors and capacitors is 20ns. The front-end circuit is designed in such a way that it can be used with either polarity of the input signal, however the full read-out chain (NMOS switches in the analogue pipeline, output multiplexer) is optimised for the p-side strips. The dynamic range of the amplifier is designed for 12fC input which together with the gain of 50mV/fC gives the full swing at the output of the front-end in the range of 600mV. The current in the input transistor is controlled by an internal DAC and can be set within the range from 0 to 320 microA. This allows one to optimise the noise according the actual detector capacitance. The design and the performance of the chip will be presented. The basic chip performance has been evaluated in the test bench. Analogue prototype module consisting of two 6.4 cm x 6.3 cm ATLAS baseline detectors read out by SCT128A chips has been built. The chips are mounted on a ceramic hybrid connected to the sensors in the end-tap configuration. The performance of the module will be presented and discussed. ***************************************************************************** Subject: leb 2001 workshop submission Date: Mon, 30 Apr 2001 12:24:51 +0200 (MET DST) From: Jan Troska To: catherine.decosse@cern.ch CC: Karl Gill Hi, I would like to submit a paper on behalf of my colleague Karl Gill: Title ----------------- Quality Assurance Programme for the Environmental Testing of CMS Tracker Optical Links Authors ----------------- K. Gill, R. Grabit, M. Hedberg, J. Troska, F. Vasey and A. Zanet CERN EP Division. Corresponding Author --------------------- Karl Gill Abstract ----------------- The QA programme for the environmental tests of the COTS components for the CMS Tracker Optical link system is presented. These tests will take place in the pre-production and final production phases of the project and will measure radiation resistance, component lifetime, and sensitivity to magnetic fields. The results are summarized from the extensive series of earlier prototype sample testing and the evolution of these small-scale tests to the pre-production final manufacturing tests is outlined. Summary ---------------- Final production of the CMS Tracker optical links will begin in 2001 and continue until 2004. Approximately 40000 uni-directional analogue optical links, and ~1000 bi-directional digital optical links will be produced during this time. Full details of the two types of optical link system, including the quantities of components and their specifications, can be found on the web[1]. Both analogue and digital optical links for the CMS Tracker share the same basic components, namely 1310nm InGaAsP/InP multi-quantum-well edge-emitting lasers and InGaAs p-i-n photodiodes coupled to single-mode optical fibre. The optical fibre is in the form of buffered single-way fibre, ruggedized 12-way ribbon fibre cable, and dense 96-way multi-way ribbon cable, with MU-type single way and MT-type multi-way optical connectors used at the various optical patch panels. All of the devices listed here are commercial off-the-shelf (COTS) components. Quality Assurance (QA) procedures have been developed in order to guarantee that the final links meet their specified performance and are produced on schedule. A full QA manual has been written and in this paper we focus on the part of the QA programme concerning environmental testing of components. The CMS Tracker environment is characterized by the high levels of radiation, up to ~2x10^14/cm^2 fluence and 100kGy ionizing dose for the optical link components over the first 10 years of operation[2]. The particle fluence at the innermost detector modules of the Tracker is dominated by pions and photons, with energies ~100MeV, and by ~1MeV neutrons at the outermost modules. In addition the components must operate in a 4T magnetic field and at temperatures close to -10§C. The extensive use of COTS components in the optical links means that all prototype devices have had to be thoroughly tested. The resistance to radiation and magnetic fields are not product characteristics that are normally specified or guaranteed by telecommunications manufacturers. In extensive prototype sample tests we have measured the radiation effects in all of the optical link components, for fluences and doses typical of CMS Tracker worst-case conditions[3]. The set of results will be summarized in the full paper. Despite having restricted the final choice of candidate components to those that have passed earlier sample tests, the use of COTS means that environmental QA testing must continue into the production phase of the project. This is simply because the factors that can affect the radiation hardness of given components are not well understood in terms of their sensitivity to any changes, however slight, in the component production method. These tests are separated into 'Advance Validation' and 'Pre-production Qualification'. In the case of the lasers, p-i-n photodiodes and the optical fibres, given the large quantities required and their observed sensitivity to radiation damage, it is desirable to do the radiation tests before the final lots have been produced and delivered to CMS. These tests are therefore carried out as Advance Validation tests which means that we will carefully screen every wafer, in the case of lasers and p-i-n photodiodes, and every glass preform, in the case of optical fibres, using a number of representative samples. It is understood that this is an unusual method of component validation, necessitating a very good working relationship with the component manufacturers. For the other components, namely the hybrids and the terminated optical cables where there are fewer devices required, or where the radiation damage is expected to be less significant, the environmental tests will be carried out as part of the more general Pre-production Qualification. [1] CMS Tracker Optical Links www pages, http://cms-tk-opto.web.cern.ch [2] CMS Tracker Technical Design Report. [3] Papers in previous LEB Workshop, RADECS and SPIE Proceedings. (1996-2001). All available at [1]. Best Regards, Jan Troska. ---------------------------------------------------------------- Dr Jan Troska Tel: +41 (0)22 767 2063 EP Division Fax: +41 (0)22 767 2800 CERN Email: jan.troska@cern.ch CH-1211 Geneva 23 Switzerland Subject: LEB2001 paper submission : Date: Mon, 30 Apr 2001 11:44:35 +0100 (BST) From: Martin Postranecky To: Catherine DECOSSE CC: "Dominic A. HAYES" , "John B. Lane" , "J.M.Butterworth" , Matthew WARREN , Martin Postranecky Dear Catherine, Below find the summary and the abstract of the paper we would like to submit for the LEB2001 in September 2001. Many thanks ! Cheers, Martin TIM ( TTC Interface Module ) for ATLAS SCT & PIXEL Read Out Electronics ======================================================================= Jonathan Butterworth, Dominic Hayes(*), John Lane, Martin Postranecky, Matthew Warren University College London, Department of Physics and Astronomy ( * now at Radiocommunications Agency, London ) SUMMARY : --------- The TIM ( TTC Interface Module ) has been designed to provide the interface between the ATLAS Level-1 Trigger and the SCT and PIXEL off-detector electronics. There will be one TIM module in each of the 9U-sized off-detector ROD ( Read Out Driver ) crates, distributing the timing, trigger and control signals to all the ROD modules in each crate via a custom-designed J3 backplane and BOC ( Back Of Crate ) modules. Each TIM receives the TTC ( Timing, Trigger and Control ) information in optical form from the LHC-standard TTC distribution system, using the standard TTCrx receiver and decoder chip to provide electrical outputs. Each TIM receives in turn the ROD BUSY signals from each ROD in the crate and transmits a masked-OR Busy signal to the Level-1 Trigger via a ROD Busy Module. Two prototype TIM modules have been manufactured last year and have been extensively tested since that time at UCL. One module has been in use in the ROD System Tests at Cambridge from May 2001. Following these tests, further TIM modules are being built to allow for further ROD System and Front End Module testing at various sites around the world. The TIM has been designed as a 9U multilayer PCB with a standard VME slave interface, with all registers and configuration, control and monitoring accessible to the local crate processor. All the major logic elements of the TIM module are contained on ten large scale PLDs ( Programmable Logic Devices ), allowing for possible future design changes by firmware modification. Each TIM is also capable of fully stand-alone operation, generating all the TTC-type signals under the control of the local processor. Each TIM can also act as a 'master' to synchronise a number of 'slave' TIM modules to allow for a stand-alone operation of a system consisting of more than one ROD crate. As well as being the 'standard' TTC Interface Module for the SCT off-detector electronics, TIMs will also be provided to the PIXEL detector community, and possibly other detectors, to provide them with the TTC interface. ABSTRACT : ---------- The design, functionality, description of hardware and firmware and preliminary results of the ROD ( Read Out Driver ) System Tests of the the TIM ( TTC Interface Module ) are described. The TIM is the standard SCT and PIXEL detector interface module to the ATLAS Level-1 Trigger, using the LHC-standard TTC ( Timing, Trigger and Control ) system. TIM has been designed and built during the year 2000 and two prototypes have been used since. More modules are being built this year to allow for more tests of the ROD system at different sites around the world. \--=-// ( o^o ) ----------------------------------------------oOOO------(_)---OOOo---- | Martin Postranecky Phone : [00-44]-(0)20-7679 3453 | | UNIVERSITY COLLEGE LONDON Phone : [00-44]-(0)20-7679 2000 | |DEPT.OF PHYSICS AND ASTRONOMY Fax: [00-44]-(0)20-7679 7145 | | High Energy Physics Group E-Mail: mp@hep.ucl.ac.uk | |Gower Street, LONDON, WC1E 6BT http://www.hep.ucl.ac.uk/ | -----------------------------------------------------ooOo-----o------- Subject: Paper to LEB2001: LHCb Timing and Fast Control Date: Mon, 30 Apr 2001 12:50:34 +0200 From: "Richard Jacobsson, CERN, (Sea Environment Assoc.)" Organization: CERN, European Org. for Nucl. Res., Geneva, Switzerland To: Catherine DECOSSE CC: Beat.Jost@cern.ch, zbig@ipj.pl.gov Dear Catherine, As an attachment to this mail you find our contribution to the LEB2001 conference. Please, send me an confirmation that you have received it. Thank you very much, Richard --------------------------------------------------------------------- The LHCb Timing and Fast Control ================================== Z. Guzik, R. Jacobsson and B. Jost To be presented by R. Jacobsson Abstract ---------------- In this paper we describe the LHCb Timing and Fast Control (TFC) system. It is different from that of the other LHC experiments in that it has to support two levels of high-rate triggers. Furthermore, emphasis has been put on partitioning and on locating the TFC mastership in one type of module: the Readout Supervisor. The Readout Supervisor handles all timing, trigger, and control command distribution. It generates auto-triggers as well as control the trigger rates. Partitioning is handled by a programmable patch panel/switch introduced in the TTC distribution network between a pool of Readout Supervisors and the Front-End electronics. Summary ---------------- The LHCb Timing and Fast Control (TFC) system is in the prototyping phase. Although the backbone of the timing, trigger and control distribution network is based on the CERN RD12 system (TTC), several components are unique to the LHCb experiment due to the fact that the readout system is different from that of the other experiments in several respects. Firstly, the LHCb TFC system has to handle two levels of high-rate triggers: a Level 0 (L0) trigger with an accept rate of maximum 1.1 MHz and a Level 1 (L1) trigger with an accept rate of maximum 60 kHz. Secondly the TFC architecture focuses on partitioning. A partition is in LHCb defined as a configurable ensemble of parts of a sub-detector, an entire sub-detector or a combination of sub-detectors that can be run in parallel, independently and with a different timing, trigger and control configuration than any other partition. Furthermore, the aim has been to locate the entire TFC mastership of a partition in a single module: the Readout Supervisor (RS). The idea is to have a pool of such Readout Supervisors, in which one is interfaced to the two central trigger decision units and is used for physics data taking. The others are fully configurable masters for testing, debugging and calibrating any partition stand-alone. The Readout Supervisors receive the LHC bunch clock via the LHC machine interface. The RS used for physics data taking also receives the L0 and L1 triggers from the central L0 and L1 decision units. One task of the Readout Supervisor is to distribute these, as well as internally generated triggers and various synchronous control commands, to the Front-End electronics via the TTC network. The L0 decisions are transmitted on channel A of the TTC system, and the L1 decision as well control commands share channel B and are transmitted as short broadcasts. The six user-definable bits of the short broadcasts allow qualifying the L1 triggers and encoding different types of control commands. The RS also acts as a trigger rate controller by converting positive trigger decisions to negative whenever data congestion occurs in the system. Fast buffers such as in the L0 Front-End electronics cannot feed back overflow signals and their occupancies are therefore emulated in the RS. Slower parts of the system signal congestion via hardware. The partitioning is implemented by introducing a programmable patch panel/switch in the TTC distribution network between a pool of Readout Supervisors and the Front-End electronics. The switch can be configured to define independent distribution networks between the Readout Supervisors and sets of sub-detector components (partitions). The Readout Supervisors can thus trigger and control different partitions independently. In order to feed back the overflow signals from different sub-detector components to the appropriate RS, a second configurable "OR switch" has been devised. It performs an OR of the signals coming from components belonging to the same partition. Subject: LEB2001 abstract Date: Mon, 30 Apr 2001 14:15:58 +0200 From: Alexander Kluge Organization: CERN To: c.decosse@cern.ch CC: "Stewart, Joanna Melanie" hi, please find in the attachment, the abstract of my submission for the LEB 2001. please apologize that the summary will be sent in a later mail. cheers, Alex --------------------------------------------------------------------- The ALICE on-detector pixel PILOT system - OPS The on-detector electronics of the ALICE silicon pixel detector (nearly 10 million pixels) consists of 1,200 readout chips, bump-bonded to silicon sensors and mounted on the front-end bus, and of 120 control (PILOT) chips, mounted on a MCM together with opto- electronic transceivers. The radiation environment in the pixel detector requires radiation tolerant components. The front-end chips are all ASICs designed in a commercial 0.25 micron CMOS technology using radiation hardening layout techniques. An 800 Mbit/s Glink- compatible serializer and laser diode driver, also designed in the same 0.25 micron process, is used to transmit data over an optical fibre to the control room where the actual data processing und event building are performed. We describe the system and report on the status of the PILOT system. Subject: LEB 2001 Abstract and Summary Date: Mon, 30 Apr 2001 14:35:42 +0200 (METDST) From: Danielle Moraes To: Catherine.Decosse@cern.ch Dear Catherine, Please find in attachment the abstract and summary for the paper, "Progress on the CARIOCA Frontend Development" Many thanks. Kind regards. +----------------------------------------------------------+ | DANIELLE MAGALHAES MORAES | +----------------------------------------------------------+ | CERN | | CH-1211 Geneva 23 | | Switzerland | | Bat. 14-4-006 Tel: +4122 767 6152 | | Email: Danielle.Moraes@cern.ch Fax: +4122 767 9425 | +----------------------------------------------------------+ | Pos-Graduacao - Instituto de Fisica - UFRJ | | Cidade Universitaria - CP 68528 | | 21945-970 Rio de Janeiro - RJ | | Brasil Tel: +5521 562-7463 | | Email: danielle@if.ufrj.br Fax: +5521 562-7368 | +----------------------------------------------------------+ --------------------------------------------------------------------- Title: Progress on the CARIOCA Frontend Development. D. Moraes(1,2), F. Anghinolfi(1), W. Bonivento(1), P. Jarron(1), W. Riegler(1), B. Schimdt(1), F. Vinci dos Santos(1), (1) CERN, CH-1211 Geneva 23, Switzerland (2) Univ. Federal do Rio de Janeiro, C.P. 68528, BR-21945-970 Rio de Janeiro, Brazil Abstract: We present recent results of an ASD frontend development in 0.25um CMOS for the LHCb muon chambers. Characteristic features of the chip are a peaking time of 10ns, input resistance of <10 Ohm, a noise of 500+39e-/pF and a fast tail cancellation shaper. We present results of a 14 channel amplifier+discriminator submission showing crosstalk and parameter variations. A negative polarity preamp version suitable for wire readout and results from a fast 2x pole/zero tail cancellation shaper are also shown. Summary: First results of a fast detector frontend prototype designed in 0.25um CMOS were presented at the last LEB meeting [1]. Here we want to present the progress on this project which is aimed at the production of an ASD chip for the 120k channels of the LHCb muon system. In addition to the ASD chip the frontend board will house a logic chip, also designed in 0.25um CMOS, that will perform simple logic functions. The advantage of an analog+digital frontend in deep submicron technology are radiation hardness, low cost and low power dissipation. The muon system detectors are wire chambers with cathode and anode readout, an average primary ionization of 100 electrons and a gas gain of 10^5. The optimum time resolution of the chambers requires a peaking time of 10ns. The high rates of up to 1MHz/channel require an ion tail cancellation as well as a baseline restoration circuit. The detector capacitance ranges from 20 to 250pF, the input resistance is required to be <50 Ohm. At the last LEB we reported the results from a positive polarity preamp+discriminator chip. In this paper we present the following: 1) Results from a submission with 14 identical positive polarity amplifier+discriminator channels showing crosstalk <1%. Channel to channel variations of different parameters are discussed as well. 2) Results from a negative polarity amplifier submission. 3) Results from an amplifier+shaper submission. The shaper contains a 2x pole/zero network optimized for an ion tail of t0=1.5ns. [1] CARIOCA : A Fast Binary Front-End Implemented in 0.25um CMOS using a Novel current-mode technique for the LHCb Muon Detector / Moraes, D ; Anghinolfi, F ; Deval, P ; Jarron, P ; Riegler, W; Rivetti, A ; Schmidt, B ; 6th Workshop on Electronics for LHC Experiments, Cracow, Poland, 11-15 Sep 2000-CERN, Geneva, 25 Oct 2000. [CERN-2000-010 ; CERN-LHCC-2000-041] Subject: Summary og Abstract LEB2001 (fwd) Date: Mon, 30 Apr 2001 14:50:13 +0200 (METDST) From: Jorgen Lien To: Catherine.Decosse@cern.ch Hi Catherine! I send you my abstract and summary, and hope to be able to give a talk in the parallell sessions. My supervisors are: Luciano Musa, CERN (where I am in the doctoral student programme) Kjetil Ullaland, Universitetet i Bergen E-mail: kjetil.ullaland@fi.uib.no Håvard Helstrup, Høgskolen i Bergen E-mail: haavard.helstrup@fi.uib.no Regards Jørgen --------------------------------------------------------------------- Name: abstract.txt abstract.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64 Description: Abstract Name: LEB2001.txt LEB2001.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64 Description: Summary Subject: Abstract for LEB2001 Date: Mon, 30 Apr 2001 16:51:28 +0400 From: salima To: Catherine.Decosse@cern.ch OPTICAL PROPERTIES OF DOPED AND INTERCALATED SINGLE CRYSTALS $TlMC_2^{VI}$ $(M-In, Ga; C-S, Se)$ E. M. Kerimova, S.N. Mustafaeva, S.I. Mekhtieva, S.M. Bidzinova, N. Z. Gasanov, A. I. Gasanov Institute of Physics, Academy of Sciences of Azerbaijan, G. Javid Prospect, 33,370143 Baku, Azerbaijan E-mail: msalima@lan.ab.az This paper deals with the investigation of optical properties of $TlGaS_2, TlInS_2, TlGaSe_2$ single crystals and influence of Fe and Cu doping and also intercalation by $Li$ ions on these properties. The following main results have been obtained. Intercalation of $TlGaSe_2$ single crystals by $Li$ ions brings about the shift of energy position of exciton absorption peak, related with direct transition to long-wave side of spectrum. In particular at $5K$ this energy shift is $\Delta E=15 meV$. As a result of intercalation the coefficient of temperature shift of this exciton peak decreased half as many in absolute value and is $\delta E^{ex}/\delta T$ within the range $20 \leq T \leq 105 K$ and $-0.25.10-4 eV/K$ at $5 \leq T \leq 20 K$. Study of absorption spectra of $TlM_{1-x}Fe_xS_2 (M-In,Ga)$ single crystals in wide temperature range $5-200K$ showed, that, in particular the width of bandgap of $TlGa_{1-x}Fe_xS_2 (x=0.001; 0.005; 0.01)$ crystals as of $TlGaS_2$ crystals increases with temperature rise. For $TlGa_{0.999}Fe_{0.001}S_2$ there have been observed exciton absorption band $(h \nu =2.58eV at T=5K)$ which with temperature rise is broadened and shifted to side of higher energy. There have been also determined values of direct optical transition in $TlIn_{1-x}Fe_xS_2 (x=0.005; 0.01)$ single crystals at 5 and 300K. Study of exciton absorption spectra of $TlInS_2$ single crystals doped by $Cu$ showed that doping leads to the shift of energy position of exciton peak to long-wave region and it also increases exciton bond energy at the absorption edge: if for $TlInS_2 =20meV$, for $Tl_{0.995}Cu_{0.005}InS_2 =31meV$, for $Tl_{0.985}Cu_{0.015}InS_2 =54meV$. Bohr radius of exciton and its effective mass are calculated. Thus, doping and intercalation of $TlMC_2^{VI} leads to modification of their absorption spectra, change of exciton characteristics, i.e. allow optical properties to be controlled. Subject: Re: call for paper LECC2001 Date: Mon, 30 Apr 2001 15:58:20 +0200 From: Joao Varela <" joao.varela"@cern.ch> Organization: CERN/LIP To: Catherine DECOSSE Dear Catherine Please find below the title, authors and abstract of a paper to be presented at the next LEB. Regards, Joao Design of a Data Concentrator Card for the CMS Electromagnetic Calorimeter Readout N. Almeida, V. Antonio, N. Cardoso, A. Correia, P. Machado, J. C. Silva, I. Teixeira, J. Varela, LIP, Lisbon and INESC, Lisbon Abstract The Data Concentrator Card is a module in the CMS Electromagnetic Calorimeter Readout System responsible for data collection in a readout crate, verification of data integrity and data transfer to the central DAQ. The DCC should sustain an average data flow of 200 Mbyte/s. In the first part of the paper we summarize the physics requirements for the ECAL readout and give results on the expected data volumes obtained with the CMS detector simulation (ORCA software package). In the second part we present the module's design architecture and the adopted engineering solutions. Finally we give results on the expected performance derived from a detailed simulation of the module's hardware. > Subject: LEB 2001 workshop submission Date: Mon, 30 Apr 2001 16:50:33 +0200 (MET DST) From: Jan Troska To: catherine.decosse@cern.ch Hi Catherine, I would like to submit the following paper: Title --------------------- Prototype Analogue Optohybrids for the CMS Outer Barrel and Endcap Tracker Authors --------------------- J. Troska, K. Gill, R. Grabit, M. Hedberg, F. Vasey and A. Zanet CERN A. Go Department of Physics, National Central University, Taiwan M.-L. Chu High Energy Physics Laboratory, Institute of Physics, Academia Sinica, Taiwan Corresponding Author --------------------- Jan Troska Abstract --------------------- Prototype analogue optohybrids have been designed and built for the CMS Tracker Outer Barrel and End Cap detectors. The total requirement for both types in CMS is 12900 that will be assembled between 2002 and 2004. Using very close to final optoelectronic and electronic components several optohybrids have been assembled and tested using standardised procedures very similar to those to be implemented during production. Analogue performance has met the specifications in all cases when operated in isolation and when inserted into the full prototype optical readout system. Summary ----------------------- The CMS Tracker optical readout system will consist of approximately 40000 uni-directional analogue optical links production of which is due to commence in 2001 and continue until 2004[1]. Within the CMS Tracker the transmitting elements of the analogue optical links will be housed on analogue optohybrids that interface directly to the silicon detector modules[2]. Either two or three laser diodes (depending upon the location within the Tracker) and the associated laser driver ASIC will be mounted on an analogue optohybrid (AOH). The total requirement of optohybrids is 4000 for the Tracker Inner Barrel and Disks, 5800 for the Tracker Outer Barrel (TOB) and 7100 for the Tracker End Caps (TEC). The availability of very close to final optoelectronic components has allowed prototyping of an AOH design suitable for the TOB and TEC detectors. The PCB design, that has been carried out by CERN and produced in Taiwanese industry, can be used in both TOB and TEC by simple differential assembly of the connector on either the top- or bottom-side of the printed circuit board. The PCB measures 23mm by 30mm, is 0.5mm in thickness and accommodates two or three laser diodes, the laser driver ASIC and associated passive components. All components mounted on the prototype optohybrids (laser diodes, laser driver, optical and electrical connectors) are final or very close to final designs. An interface to the final cooling arrangement within the TOB and TEC has also been incorporated. Two types of candidate laser diode from different manufacturers have been assembled onto prototype optohybrids which have then been submitted to a full test of the specifications to demonstrate that they will meet the requirements of use within the CMS Tracker optical readout system. Prototype optohybrids have been evaluated using the standard CMS Tracker test methods described previously[3,4]. The testing carried out has demonstrated the required performance in response to both static and dynamic test suites that mimic operation within the full analogue optical link system. Noise is within the system specification of 48dB and integral non-linearity within the operating range of the optical links meets the target of 1%. Dynamic measurements show that the bandwidth of the components is not degraded by placement on the optohybrid adding further weight to the validation of the optohybrid design. Measurements have been carried out at room temperature, 0øC, -10øC and -20øC and although some variations in the laser characteristics were observed these did not significantly degrade their performance in the optical readout system. In addition to the standalone lab testing using standard procedures the analogue optohybrid prototypes were re-tested in a full optical readout system with a close to final design of the 12-way analogue receiver module. Results of these tests show that the prototype optohybrids perform well in this environment. Once validated the prototype optohybrids of TOB type will be included in the electronic system test carried out at CERN where their performance will be assessed as part of the entire electronic readout system of the CMS Tracker. [1] The Tracker System Project Technical Design Report, CERN/LHCC 98-6, CMS TDR 5, 15 April 1998 & Addendum CERN/LHCC 2000-016, CMS TDR 5 Addendum 1, 21 February 2000 [2] Specifications of the Optical Link System are available from URL http://cern.ch/cms-tk-opto [3] A 4-channel parallel analogue optical link for the CMS-Tracker, F.Vasey et al., Proc. of the fourth workshop on electronics for LHC experiments, Rome, 1998, pp. 344-348 [4] Evaluation and selection of analogue optical links for the CMS tracker - methodology and application, F.Jensen et al., CMS Note 1999/074 Best Regards, Jan. ---------------------------------------------------------------- Dr Jan Troska Tel: +41 (0)22 767 2063 EP Division Fax: +41 (0)22 767 2800 CERN Email: jan.troska@cern.ch CH-1211 Geneva 23 Switzerland Subject: LEB 01 @ Stockhoml Date: Mon, 30 Apr 2001 14:56:43 GMT From: daniel dzahini To: catherine.decosse@cern.ch CC: dzahini@isn.in2p3.fr Dear Catherine. Here is attached the summary and Abstract we intend to present during the next LEB Workshop. Best regards Daniel DZAHINI --------------------------------------------------------------------- Development of a DMILL radhard multiplexer for the ATLAS Glink optical link and radiation test with a custom Bit ERror Tester. Daniel Dzahini, for the ATLAS Liquid Argon Collaboration Institut des Sciences Nucléaires 53 avenue des Martyrs,38026 Grenoble Cedex France Abstract: A high speed digital optical data link has been developed for the front-end readout of the ATLAS electromagnetic calorimeter. It is based on a commercial serialiser commonly known as Glink, and a vertical cavity surface emitting laser. To be compatible with the data interface requirements, the Glink must be coupled to a radhard multiplexer that has been designed in DMILL technology to reduce the impact of neutron and gamma radiation on the link performance. This multiplexer features a very sever timing constraints related both to the Front-End Board output data and the Glink control and input signals. The full link has been successfully neutron radiation tested by means of a custom Bit ERror Tester. Summary The Liquid Argon Calorimeter of the ATLAS experiment at the LHC is a highly segmented particle detector with approximately 200 000 channels. The signals are digitized on the front-end board and then transmitted to data acquisition electronics situated 100m to 200m away. The front-end electronics has a high degree of multiplexing allowing the calorimeter to be read out over 1600 links each transmitting 32 bits of data at the bunch crossing frequency of 40.08 Mhz. The radiation hardness is a major consideration in the design of the link, since the emitter side will be exposed to an integrated fluence of 3*1014 n (1 MeV Si) per cm2 of the components' surface over 10 years of the LHC running. The demonstrator link is based on an Agilent Technologies HDMP1022/1024 serialiser/deserialiser. This Glink is used in a double frame mode: the incoming 32 bit digitized data at 40.08 Mhz are multiplexed into 16 bits at 80.16 Mhz. A multiplexer ASIC has been developed in the DMILL technology. This MUX chip translates first the data from LVDS level to CMOS level then it performs the data registration and multiplexing. The 16 bit data words are loaded at the input of the HDMP1022 serialiser. The Glink chip set adds a 4 bit control field to each 16 bit data segment which results in a total link data rate of 1.6 Gb/s. The Glink serialiser outputs drive a VCSEL that transforms the electrical signal into light pulses transmitted over a Graded Index (GRIN) 50/125 mm multimode fibre to a PIN diode located on the receiver board. For the link described in this document the VCSEL and the PIN diode are packaged together with driving and discriminating circuits as transceiver modules manufactured by Methode. The PIN diode output signals are deserialised by the GLINK HDMP1024 chip. A Programmable Logic Array (ALTERA EMP7128) is placed on the receiver board to facilitate demultiplexing. Several link sender boards were exposed to neutron flux to assess the radiation tolerance of the DMILL MUX, the Glink serialiser and the Methode transceiver. During the radiation tests, the behaviour of the link was monitored on-line. A Bit ERror Tester (BERT) coupled to a pseudo-random pattern generator was specially developed. The BERT consists in a modular tester it permits several high speed (32 bit at 40.08 Mhz) data links to be tested simultaneously. The single bit error detection is performed by comparison of sent and transmitted bit. The BERT comprises EPLD based boards plugged in a VME crate. The slow control and the error acquisition is done on-line by a Personal Computer. The radiation tolerance of the sender part of the link has been demonstrated under neutron radiation up to 1014 n cm-2. Transient data transmission errors (Single Event Upset) were observed by means of the BERT set-up but it has been shown that the contribution of the DMILL MUX to this error rate is very negligible. Subject: LEB abstract Date: Mon, 30 Apr 2001 17:47:08 +0200 From: Helfried BURCKHART Organization: CERN To: Catherine Decosse CC: Fernando Varela Rodriguez , Jim Cook , Bjorn Hallgren Dear Mme Decosse, please find enclosed the abstract of our contribution to the LEB 2001. The summary will follow next week. best regards, Helfried Burckhart Title: "Vertical Slice of the ATLAS Control System" Authors: H.J.Burckhart, J.Cook, B. Hallgren, F.Varela, CERN-EP Viatcheslav Filimonov, PNPI, St.Petersburg, Russia The ATLAS Detector Control System (DCS) consists of two main components: a distributed supervisor system, running on PCs, and the different front-end systems. For the former the commercial SCADA package, PVSS-II, has been chosen together with the CERN Joint Controls Project, JCOP. For the latter, a general purpose I/O concentrator called the "Embedded Local Monitor Board" (ELMB) has been developed, which is based on the CAN fieldbus. The paper describes a full vertical slice of the DCS, including the interplay between the ELMB and PVSS-II. Examples of typical control applications will be given. |==========================================| | Dr. Helfried Burckhart | | European Laboratory for Particle Physics | | CERN, EP | | CH-1211 Geneva 23 | | | | Tel: (+41) 22 767 12 54 | | Fax: (+41) 22 767 83 50 | | e-mail: Helfried.Burckhart@cern.ch | |==========================================| Subject: abstract & summary for LEB2001 Date: Mon, 30 Apr 2001 18:36:50 +0200 (MET DST) From: Guido Magazzu To: Catherine DECOSSE CC: Marchioro Alessandro , Paulo.Moreira@cern.ch, Guido.Magazzu@pi.infn.it Dear Catherine, please find enclosed title, list of authors, abstract and summary of our paper for LEB2001. Regards, Guido Magazzu'. Title A rad-hard 8-channel 12-bit resolution ADC for slow control applications in the LHC environmnent Authors G.Magazzu' - INFN Sezione di Pisa A.Marchioro, P.Moreira - CERN Abstract A key component for monitoring environmental parameters like temperature, silicon detector leakage currents, power supply voltages and currents in the LHC detector environment is a rad-hard, low-power multi-channel A/D converter. For these applications in the CMS central tracker we have designed and developed an integrated circuit, the Detector Control Unit (DCU). The core of the DCU is an 8-channel 12-bit A/D converter controlled through a standard I2C interface. The structure and the performance of this ADC are desribed in the paper. Summary Silicon detectors, when exposed to the high level of radiation in the LHC experiments, are subject to a number of damaging phenomena demanding careful monitoring of their environmental conditions. In the CMS central tracker the detector leakage currents in the range of 100uA to 10mA are measured using sensing resistors and the temperature in the range of -20 deg C to +20 deg C is monitored using appropriate thermistors. The supervision of other parameters like the local supply voltages and the temperature of the hybrids housing the front-end integrated circuits is also performed. All these quantities need to be read and logged with relatively low frequency, therefore a fast conversion time is not required. A highly integrated and low-power solution is required because of the strict requirements in terms of space and power dissipation. The Detector Control Unit (DCU) has been developed to perform all the requested functions in one single integrated circuit. This ASIC consists basically of a 12-bit A/D converter that uses a single slope architecture, preceded by an 8 input analog multiplexer. 8 inputs are available to measures voltages in the range 0V to 2.5V (rail-to-rail, since the power supply voltage is 2.5V). The A/D conversion time is ~0.2ms. Two operating modes are available: in the "low input range" mode (0V to 1.5 V) the input signal is referenced to GND while in the "high input range" mode (1.0V to 2.5V) the signal is referenced to VDD. In both operating modes the measured non-linearity is less than 1 LSB with no missing codes. To achieve the rail-to-rail input compatibility the analog circuitry uses a complementary solution based on a pair of NMOS and PMOS comparators and has an automatic offset cancellation scheme. A 100pF metal-to-metal capacitor is charged from GND or discharged from VDD, according to the selected mode, using stable and temperature independent currents derived from an on-chip band-gap reference. Two temperature independent and stable current reference outputs (10uA and 20uA) are also provided to bias the external temperature sensing thermistors. A custom on-chip temperature sensor measures the temperature of the substrate housing the ASIC. The DCU is interfaced to the Tracker Control System via a standard I2C port, through which the user can start an on-chip temperature sensor acquisition, fix the A/D converter operating mode, select one of the 8 inputs, start an A/D conversion and read the conversion result. The digital part of the chip uses triple redundancy and majority voting to ensure protection against SEU effects. The DCU is designed in a commercial quarter micron technology using special layout techniques to enhance its radiation tolerance. The total chip area measures 2.0x2.0 mm2, contains 28 pins and the power consumption is less than 50mW. The circuit has been submitted to fabrication and fully characterized. Its architecture and the measured performance will be presented in the paper. Subject: Abstract for LEB 2001: CMS REGIONAL CALORIMETER TRIGGER JET LOGIC Date: Mon, 30 Apr 2001 11:51:56 -0500 From: "Wesley H. Smith" Organization: University of Wisconsin To: Catherine.Decosse@cern.ch CMS REGIONAL CALORIMETER TRIGGER JET LOGIC P. Chumney, S. Dasu, F. di Lodovico, M. Jaworski, J. Lackey, P. Robl, W.H. Smith University of Wisconsin - Madison The CMS regional calorimeter trigger system detects signatures of electrons/photons, taus, jets, and missing and total transverse energy in a deadtimeless pipelined architecture. This system contains 19 crates of custom-built electronics. Recent changes to the Calorimeter Trigger have been made to improve the efficiency and purity of jet and tau triggers. The revised algorithms, their implementation in hardware, and their performance on physics signals and backgrounds are discussed. Wesley H. Smith University of Wisconsin Physics Department 1150 University Ave. Madison, Wisconsin 53706 USA tel: (608)262-4690, fax: (608)263-0800, email: wsmith@wishep.physics.wisc.edu CMS REGIONAL CALORIMETER TRIGGER JET LOGIC P. Chumney, S. Dasu, F. di Lodovico, M. Jaworski, J. Lackey, P. Robl, W.H. Smith University of Wisconsin - Madison The CMS Regional Calorimeter Trigger receives compressed data from the calorimeter readout electronics on 1.2 GBbaud copper links, each carrying data for two HCAL or ECAL trigger towers. 19 total crates (18 for the barrel/endcap and one for both forward calorimeters) each contain seven rear mounted Receiver cards, seven front mounted Electron Isolation cards, and one front mounted Jet Summary card plugged into a custom point-to-point 160 MHz differential ECL backplane. Each crate transmits to the global calorimeter trigger processor its sum Et, missing energy vector, 4 highest-ranked isolated and non-isolated electrons, and 4 highest energy jets and 4 tau-tagged jets along with their locations. The jet trigger uses the transverse energy sums (e.m.+had) computed in calorimeter regions (4x4 trigger towers), except in the HF region where it is the trigger tower itself. The input tower Et is coded in an 8 bit linear scale with programmable resolution. The subsequent summation tree extends to a 10 bit linear scale with overflow detection. Simulation studies showed that a scale of 10 bits with LSB = 1 GeV gives adequate jet trigger performance. The jet trigger uses a 3x3 calorimeter region sliding window technique which spans the complete (eta, phi) coverage of the CMS calorimeters seamlessly. The central region Et is required to be higher than the eight neighbour region ET values. The jets and taus are characterized by the transverse energy Et in 3x3 calorimeter regions. The summation spans 12x12 trigger towers in barrel and endcap or 3x3 larger HF towers in the HF. The jets are labelled by (eta, phi) indexes of the central calorimeter region. For each calorimeter region a tau-veto bit is set ON if there are more than two active ECAL or HCAL towers in the 4x4 region. A jet is defined as "tau-like" if none of the 9 calorimeter region tau-veto bits are ON. The four highest energy central and forward jets, and central taus in the calorimeter are selected. Jets and taus occurring in a calorimeter region where an electron is identified are not considered. The selection of the four highest energy central and forward jets and of the four highest energy taus provides enough flexibility for the definition of combined triggers. In addition counters of the number of jets above programmable thresholds in various eta regions are provided to give the possibility of triggering on events with a large number of low energy jets. Jets in the forward and backward HF calorimeters are sorted and counted separately. The baseline implementation of jet clustering is based on the 160 MHz ASICs and point-to-point backplane technology developed for the CMS regional calorimeter electron/photon trigger. The entire eta-phi plane is covered by a single cluster crate that receives data from 18 Regional Calorimeter Trigger crates on parallel differential ECL links at 80 MHz and processes the data at 160 MHz. Another implementation under study incorporates the algorithm into the FPGA logic of the CMS Global Calorimeter Trigger. -- *** please note new email address: wsmith@hep.wisc.edu *** ===================================================================== | Prof. Wesley H.Smith | Ph: 608-262-4690 or 2281, Fax:608-263-0800 | | High Energy Physics | Physics Dept., University of Wisconsin | | 4275 Chamberlin Hall | 1150 University Ave.,Madison WI 53706-1390 | | wsmith@hep.wisc.edu | http://hep.wisc.edu/wsmith/ | ===================================================================== Subject: LEB'01 abstract and summary Date: Mon, 30 Apr 2001 13:24:20 -0400 (EDT) From: Alexander Madorsky To: Catherine.Decosse@cern.ch CC: Darin Acosta Dear Catherine, please find in the attachment the abstact and summary of the talk "THE TRACK-FINDING PROCESSOR FOR THE LEVEL-1 TRIGGER OF THE CMS ENDCAP MUON SYSTEM". Regards. Alex Madorsky University of Florida/Physics Museum rd & NS dr Gainesville, FL, 32606, USA 1-352-392-9849 fax: 352-392-8863 --------------------------------------------------------------------- Name: leb01.txt leb01.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64 Description: ASCII file of abstract Name: leb01_summary.txt leb01_summary.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64 Description: ASCII file of summary Subject: Talk at LEB2001 Date: Mon, 30 Apr 2001 19:36:26 +0200 From: Ulrich Trunk Organization: University of Heidelberg To: Catherine.Decosse@cern.ch Dear Catherine, I would like contribute to the "electronics for trackers" session at LEB2001 in Stockholm. The title will be: "Enhanced radiation hardness and faster front ends for the Beetle readout chip" Abstract and summary are attached to this mail. With best regards Ulrich Trunk -- ---------------------------------------------------------------------- AAAAAAAH HH Dr. Ulrich Trunk AA AH HH Max-Planck-Institut fuer Kernphysik AA LL AH HH ASIC Labor Heidelberg AA LL AH HH Tel: +49 6221 544324 Schroederstrasse 90 AA LL AH HH Fax: +49 6221 544345 D-69120 Heidelberg LL mailto:trunk@kip.uni-heidelberg.de AA LLLLLLLL http://wwwasic.kip.uni-heidelberg.de/~trunk/ ---------------------------------------------------------------------- --------------------------------------------------------------------- Title ----- Enhanced radiation hardness and faster front ends for the Beetle readout chip Authors list ------------ Niels van Bakel, Jo van den Brand, Hans Verkooijen (Free University of Amsterdam / NIKHEF Amsterdam) Daniel Baumeister, Werner Hofmann, Karl-Tasso Knoepfle, Sven Loechner, Michael Schmelling, Edgar Sexauer^(*), Ulrich Trunk (Max-Planck-Institute for Nuclear Physics, Heidelberg) Martin Feuerstack-Raible (University of Heidelberg) Neville Harnew, Nigel Smale (University of Oxford) ^(*) now at Dialog Semiconductors, Kirchheim-Nabern, Germany Abstract -------- Beetle 1.0 and 1.1 are pipelined 128 channel front end chips for the LHCb experiment, manufactured in 0.25 mu m standard CMOS technology. The final version of this chip will be equipped with SEU resistant control circuitry and a fast front end with improved analogue performance. Three chips containing prototype components have been submitted in May 2001. Descriptions of the concepts implemented in the BeetleFE1.1, BeetleFE1.2 and BeetleSE1.0 chips are presented together with simulation- and first test results. Summary ------- Beetle 1.0 and 1.1 are pipelined 128 channel front end chip for the LHCb, experiment manufactured in 0.25 mu m standard CMOS technology. The chip hast to meet the requirements of the silicon vertex detector, inner tracker, the pile-up veto trigger and the RICH in case of multi-anode photomultiplier readout. The chip can be operated in analogue as well as binary readout mode. The latest version was submitted in March 2001. Each of the chip's 128 channels features an analogue front end consisting of a charge sensitive preamplifier, an active CR-RC pulse shaper and a buffer. Its preamplifier and shaper stages use the well known folded cascode topology, the preamplifier features an NMOS input transistor. The current front end satisfies the requirements of rise below 25 ns and a remainder of at most 30% of the maximum pulse height 25 ns after the peak for a load capacitance below 15 pF. This is sufficient for applications in the LHCb vertex detector. Higher detector capacitances as expected for the inner tracker and robust operation also for large occupancies, however, call for a faster pulse shapes with a lower remainder after 25 ns. To study possible improvements, four additional front end prototypes were developed and implemented on the BeetleFE1.1 and Beetle FE1.2 chips. The control circuit of the Beetle heavily relies on registers, either to store configuration data, or to implement state machines. To overcome SEU failures in these registers, a parity based error correction schema (ECC) is implemented for static registers on the BeetleSE1.0, while the registers in its state machines use triple redundancy to suppress SEU failures. The components on these chips will be included in the pipelined readout chip Beetle1.2 which is intended for submission in 2002. The circuits on the BeetleFE1.1, BeetleFE1.2 and BeetleSE1.0 chips submitted in May 2001 are presented together with simulation- and test results and descriptions of the concepts implemented on these chips. Subject: LEB 2001 Abstract submission Date: Mon, 30 Apr 2001 21:29:52 +0200 From: Enzo CARRONE Organization: CERN To: Catherine.Decosse@cern.ch Dear Mrs. Decosse, below you can find the abstract for the next LEB 2001 workshop. I am currently working for the ALICE-HMPID group (along with Eugenio Nappi and Giacinto De Cataldo) to the ALICE Detector Control System (DCS). The abstract has already been read and approved by Guy Paic and Paolo Giubellino. I am permanently at CERN so, please, do not hesitate to contact me for any kind of question. Thank you very much. Very truly yours, Enzo Carrone. PRESENTER: Enzo Carrone for the ALICE collaboration - CERN CH1211, Geneva 23, Switzerland CONTACT: Enzo Carrone CONTACT EMAIL: Enzo.Carrone@cern.ch TITLE: Design specifications and simulation of the HMPID's control system in the ALICE experiment. AUTHORS: E.Carrone†††, M. Davenport††, G. De Cataldo†, A. Franco†, P. Martinengo††, E. Nappi† ABSTRACT: The HMPID (High Momentum Particle Identification Detector) detector is one of the ALICE (A Large Ion Collider Experiment) subdetectors planned to take data at LHC at the beginning of 2005. Since ALICE will be located underground, the HMPID will be remotely controlled by a Detector Control System (DCS), which consists of three layers: physical, control and supervisory. The first one includes sensors, actuators and the detector, the second one deals with the device where the control programs run, and finally the supervisory layer contains the Machine-Man Interface (MMI), which lets the user run the DCS. In this paper we will present the DCS design, accomplished via GRAFCET (GRAphe Fonctionel de Commande Etape/Transition), a tool which represents the DCS as a finite state machine, and then translated into code readable by the PLC (Instruction List) via an ad hoc algorithm. The SCADA DCS is based on PVSS, a commercial software. The results achieved so far show that this way of proceeding is effective and time saving, since every step of the work is autonomous, making simpler the debugging and updating phases. ††† Politecnico di Bari, Italy and CERN, Switzerland †† CERN, Switzerland † INFN Bari, Italy -- Enzo Carrone CERN 1-R-035 CH1211, Geneva 23 - Switzerland e-mail: Enzo.Carrone@cern.ch phone no. +41-22-76 71935 Subject: Abstract and Summary for LEB 2001 Date: Mon, 30 Apr 2001 14:34:46 -0500 From: Eric Hazen To: Catherine.Decosse@cern.ch CC: rohlf@bu.edu, wusx@bu.edu, drew@physics.umd.edu, tullio@physics.umd.edu, adams@uic.edu Hello Catherine- Please find attached an abstract and summary for a paper to be presented at the LEB 2001 conference in Stockholm. Please contact me regarding this paper. Regards, Eric Hazen --------------------------------------------------------------------- Name: abstract.txt abstract.txt Type: Plain Text (text/plain) Description: abstract.txt Name: new_summary.txt new_summary.txt Type: Plain Text (text/plain) Description: new_summary.txt --------------------------------------------------------------------- +----------------------------------------------------------------------+ | Eric Hazen | Phone: 617/353-6120 | Fax: 617/353-3331 | hazen@bu.edu | | Boston University Physics Dept | http://ohm.bu.edu/~hazen | | Schedule at http://calendar.yahoo.com/public/eshazen/ | +----------------------------------------------------------------------+ Subject: Corrected abstract and summary Date: Mon, 30 Apr 2001 17:36:59 -0500 From: Gabriele_Chiodini To: Catherine.Decosse@cern.ch, chiodini@fnal.gov Sorry, but we added a small correction to the abstract and summary just send it. Here it is the new abstract and summary of our contribution to the workshop. Abstract: We report on several irradiation studies performed on BTeV pixel readout chip prototypes exposed to a 200 MeV proton beam at Indiana University Cyclotron Facility. The pixel readout chip preFPIX2 has been developed at Fermilab for collider experiments and implemented in standard 0.25 um CMOS technology following radiation tolerant design rules. The tests confirmed the radiation tolerance of the chip design to proton total dose up to 14 MRad. In addition, non destructive radiation-induced single event upsets have been observed in on-chip static registers and the single bit upset cross section has been measured. We also show irradiation test results that we are planning to do on June-July 2001, where preFPIX2 readout chips bump-bonded to pixel sensors will be exposed to high dose. Summary: The BTeV experiment is planned to run at the Tevatron collider in ~2006. It is design to cover the ``forward'' region of the p-antip interaction point at the expected luminosity of 2E32/s/cm**2$. The experiment will employ a silicon pixel vertex detector to provide high precision space points for on-line lowest level trigger impact parameter finding. The ``hottest'' chip, located at 6 mm from the beam, will experience a fluence of ~ 1E14/cm**2/y. This correspond to the highest radiation enviroments at ATLAS and CMS at LHC. A pixel detector readout chip (FPIX) has been developed at Fermilab to meet the requirement of Tevatron collider experiments. The preFPIX2 reppresents the most advanced iteration of very succesfull chip prototypes and has been realized in standard deep-submicron CMOS technology from two vendors. As demostrated by the RD49 collaboration at CERN, the above process can be made very radiation tolerant following specific design rules. We show results of radiation tests performed this year with preFPIX2 chip prototypes including both total dose and single event effects. The tests have been performed by exposing the chip to 200 MeV protons (at the Indiana University Cyclotron Facility). The comparison of the chip performace before and after exposure shows the high radiation tolerance of the design to hadrons up to ~ 14 Mrad total dose. Last year exposures to radiation from a Colbalt-60 source at Argonne National Lab already verified the high radiation tolerance to gamma radiation up to ~ 30 Mrad total dose. Total dose effects are not the only concern for reliable operation of the detector. Ionizing radiation can induce single event upset (SEU) effects, as unwanted logic state transition in a digital device, corrupting stored data. The single event upsets just described do not permanently alter the chip behavior, but they could result in data losses, shifts of the nominal operating conditions, and loss of the chip control. If the single event upset rate is particularly high it could be significantly mitigated by circuit hardering techniques. Instead, if it is not, it could be tollerated simply by a slow periodic downloading of potentially corrupted data or full system resetting in the worse case. During the irradiation tests, we observed single event upsets in the preFPIX2 registers and measured the rate. The measurements consisted of detecting bit error rates in the static registers controlling the readout chip front-end operating conditions and the pixel cell respons. The single bit upset cross section measured for the digital-analog-converter registers located on the chip periphery was sigma = 3.8(+/-1.2 +/- 0.2)E-16cm**2, while for the mask and charge-injection registers located inside each pixel cell was sigma = 2.0(+/-0.3+/-0.1)E-16cm**2 (where the first error is statistical and the second systematic due to uncertainty in the beam fluence). The implications of the estimated SEU rate in the BTeV pixel vertex detector are discussed. We would like also to report results from irradiation tests planned for June-July 2001 with single chip sensor bump-bonded to a readout chip. In these future test, the primary goals are to increase the statistics of single event upsets and compare the front-end performance before and after irradiation of the assembly sensor-readout chip. Thanks, Gabriele -- Gabriele Chiodini Particle Physics Division, MS#122 (WH 10W) chiodini@fnal.gov Fermi National Accelerator Laboratory Phone: (630) 840-5151 P.O. Box 500 Fax: (630) 840-3867 Batavia, IL 60510 Subject: Paper for LEB 2001 Date: Tue, 1 May 2001 08:02:55 +0100 From: Tony Weidberg To: "'Catherine.Decosse@cern.ch'" Dear Catherine, I am sorry this is slightly late but I hope you can still conisder it. Please find enclosed an abstract and summary for a paper for the LEB 2001 workshop. Regards Tony <> <> ______________________________________________ Tony Weidberg Physics Department Oxford University Oxford OX1 3RH UK phone: +44 (0) 1865 273370 fax: +44 (0) 1865 273417 email: t.weidberg1@physics.ox.ac.uk ______________________________________________ --------------------------------------------------------------------- leb2001_abstract.txtName: leb2001_abstract.txt Type: Plain Text (text/plain) leb2001_summary.txtName: leb2001_summary.txt Type: Plain Text (text/plain) Subject: LECC2001 Abstract for a paper (repeat) Date: Tue, 1 May 2001 10:21:52 -0500 From: Selcuk Cihangir To: CC: "W.L. Simon Kwan" , Selcuk Cihangir Hello Ms. Decosse, I believe there was a formatting problem in the first mail I sent. I am re-sending the mail. I hope this will not have the same problem. Please disregard the first mail. Thank you. Selcuk Cihangir Fermilab Particle Physics Division selcuk@fnal.gov ====================================================================== Hello, Following are the Abstract and the Summary for a paper we would like to present at the LECC2001 Workshop. Thank you, Selcuk Cihangir and Simon Kwan Fermilab, USA =================================================================== Study of thermal cycling and radiation effects on Indium and fluxless solder bump-bonding devices Abstract: Pixel detectors proposed for the new generation of hadron collider experiments will use either indium or Pb/Sn solder bump-bonding technology. We have carried out a study of long term effects of both types of bump bonds using daisy-chained silicon on silicon parts. We also studied the effect of thermal cycles. Some of the parts were then exposed to intense radiation using a gamma source and the integrity of the bumps were studied afterwards. Summary: Pixel detectors propsoed for the new generation of hadron collider experiments will use flip-chip mating technology based on either indium or solder bumps to connect the sensors to the readout chips. Last year, we reported a large scale tests of the yield using both technologies. The conclusion is that both seem to be viable for pixel detectors. We have recently carried out a study of long term effects of both types of bump bonds using daisy-chained parts. We also studied the effect of thermal cycles by heating the parts to 100 C for 2 days and cooling them down to -15 C for up to a week. Some of the parts were then exposed to intense radiation using a gamma source and the integrity of the bumps was studied afterwards. In indium bump bonds, we observed in some channels a substantial increase in resistance along with occurance of capacitance of 50 - 300 pf. All three processes, namely long term storage, heating and cooling, caused this effect. We will quote rates for this effect. In solder bump bonds, the effect was the breakage of the bonds at some channels. Some of these breakages may have had occured at the UBM (Under Bump Metalization) level. All three processes caused breakage of the bonds. We will quote rates for their occurances at the UBM level and otherwise. Among the three processes, cooling was the least problematic. For some channels, the heating process helped to improve the connectivity. Subject: LEB contribution Date: Wed, 2 May 2001 00:24:47 +0200 (CEST) From: Zdenek Dolezal To: Catherine.Decosse@cern.ch Dear Catherine, I have to apologize for late sumbission of LEB talk, but there were 2 national holidays in our country and I had troubles to get on internet - I managed only now. I hope my two submissions will still be considered for LEB. Regards, Zdenek Dolezal --------------------------------------------------------------------- Name: LEB1.txt LEB1.txt Type: Plain Text (TEXT/plain) Encoding: BASE64 Subject: LEB submission 2 Date: Wed, 2 May 2001 00:27:21 +0200 (CEST) From: Zdenek Dolezal To: Catherine.Decosse@cern.ch Dear Catherine, apologies once more... (see previous mail) Regards, Zdenek Dolezal --------------------------------------------------------------------- Name: LEB2.txt LEB2.txt Type: Plain Text (TEXT/plain) Encoding: BASE64 Subject: Summary LEB2001 Date: Wed, 02 May 2001 00:16:40 -0500 From: Claudio Rivetta Organization: Fermi National Accelerator Lab. To: Catherine.Decosse@cern.ch Hi Catherine; I am sorry I am sending the summary after April 30. I hope it is not a problem. The area should be "Low voltage and high voltage distribution" Please let me know if you have problems editing the abstract and summary. Thank you CLaudio --------------------------------------------------------------------- EMI Filter Design and Stability Assessment of DC Voltage Distribution based on Switching Converters B. Allongue, F. Arteche, F. Szoncso CERN CH-1211 Geneve 23 Switzerland C. Rivetta FERMILAB P.O.500 MS 222 Batavia Il 60510 U.S.A. Abstract The design of DC power distribution for LHC front-end electronics imposes new challenges. Some CMS sub-detectors have proposed to use a DC-power distribution based on DC-DC power switching converters located near to the front-end electronics. DC-DC converters operate as a constant power load. They exhibit a dynamic negative impedance at low frequencies that can generate interactions between switching regulators and other parts of the input system resulting in system instabilities. In addition, switching converters generate interference at both input and output terminals and can compromise the operation of the front-end electronics and neighboring systems. Appropriated level of filtering is necessary to reduce this interference. This papers address the instability problem and present methods of modeling and simulation to assess the system stability and performance. The paper, also, addresses the design of input and output filters to reduce the interference and achieve the performance required. Summary EMI Filter Design and Stability Assessment of DC Voltage Distribution based on Switching Converters A distinguish feature of LHC detectors is the enormous number of channels in the front-end electronics (FE) in all the sub-parts. It requires low-voltage output power supplies in the range of multi-kilowatts to bias such electronics read-outs. To minimize the volume of the distribution cables, some CMS sub-detectors are developing a DC power distribution based on DC-DC switching converters located near to the FE in the detector caverns. Switching power supplies, in general, generate more noise than equivalent linear power supplies. In DC power distributions for FE, it is very important to keep the noise up to a level that does not compromise the operation of the FE and neighboring systems. Output filters into these converters are included to smooth the switched output voltage waveform to levels than can be tolerated by the FE. Input filters are needed to attenuate the switching input current waveform to prevent electromagnetic interference problems and to assure electromagnetic compatibility with neighboring systems. These input filters can also significantly affect the stability and performance of DC-DC converters. Input filters can introduce instabilities in the system. DC-DC switching converters with tight output voltage regulation operate as constant power loads. In such cases, the instantaneous value of the input impedance is positive, but the incremental input impedance is negative. Due to the negative impedance characteristic of switching regulators, interaction between those units and other parts of the system may result in system instability. Interference that is emitted by DC-DC converters can be either conducted or radiated. In general, interference covers a broad range of frequencies. Inputs and output filters consist of two distinct filter sections. The larger, lower frequency section is included to minimize the differential-mode noise (DMN) produced by the converter. The higher frequency section has a special topology to attenuate both differential and common-mode noise (CMN). The last component is due to currents flowing to ground through parasitic elements of the converter. Commercial converters include part of these filters. Our goal is to include additional filtering to further reduce both common-mode and differential mode noise at the input and output of the converter. The most critical is the input filter because the primary requirements are: Sufficient attenuation of both DMN and CMN components, stability and good performance of the complete system and also minimum size and reliability. To define the additional level of attenuation, DMN and CMN measurements of the input and output currents are necessary. The separation of noise components into CM and DM components simplify the filter design. The filter topology allows designing the elements that attenuate the CM noise almost independently of those elements that affect the DM noise components. Also this filter has influence at high frequency and its effect at low frequency can be ignored. To assess stability and performance a model of the complete system is necessary. It includes not only all the DC-DC converters connected in parallel at the input but also the cable impedance and the output impedance of the primary AC/DC converter. Large-signal and small signal analysis is used to define the necessary damping to include into the input filter to satisfy the required performance. Subject: Re: Forwarded mail.... Date: Wed, 2 May 2001 14:23:14 +0200 (MEST) From: HU Christine To: Catherine DECOSSE CC: HU Christine Dear Catherine, Sorry for missing the title. You could be fine here the title: --------------------------------------------------------------------- The HAL25 Front-end chip for the ALICE Silicon Strip Detectors --------------------------------------------------------------------- Cheers, Christine On Mon, 30 Apr 2001, Catherine DECOSSE wrote: > Dear Christine, > > Thank you for your submission. > WOuld you please send me a title... > Regards > Catherine > > HU Christine wrote: > > > > Dear Catherine, > > > > Please find here after our paper fot the 7th workshop on Electronics for LHC > > experiments. > > > > Christine HU > > > > ============================================================================ > > > > ABSTRACT > > -------- > > The HAL25 is a mixed low noise, low power consumption and radtol ASIC intended > > for read-out of Silicon Strip Detectors (SSD) in the ALICE tracker. It is > > designed in a 0.25 micron CMOS process and is similar in concept to the previous > > chip ALICE128C. The chip contains 128 channels of preamplifier, shaper and a > > capacitor to store the charge collected on a detector strip. The analogue data > > is held by an external logic signal and can be serially read out through an > > analogue multiplexer. A slow control mechanism based on JTAG protocol was > > implemented for a programmable bias generator, an internal calibration system > > and selection of functional modes. > > > > SUMMARY > > ======= > > > > The HAL25 chip is a mixed analogue-digital ASIC designed for read-out of > > Silicon Strip Detectors (SSD) in the ALICE tracker. It is based on the ALICE > > first generation chip ALICE128C which was tested with good performance for an > > irradiation up to 50 krad. ALICE128C is now used in the SSD frontend > > electronic of the STAR tracker. > > > > For the ALICE experiment, a new radiation hardened circuit design was required > > to meet the total dose radiation and latchup background. It has been > > demonstrated that commercial deep submicron CMOS technologies exhibit intrinsic > > radiation tolerance. HAL25 has been designed with special design technics in a > > 0.25 micron CMOS process which is expected to meet the demands of low noise, low > > power consumption and radiation hardness required by the ALICE experiment. > > > > HAL25 contains 128 channels of preamplifier, shaper and a capacitor to store the > > charge collected on a detector strip. The data is held by an external logic > > signal and can be serially read out through an analogue multiplexer at 10 MHz. > > The chip is programmable by the JTAG protocol which allows: > > - to set up an adjustable bias generator which tunes the performances > > of analogue chains; > > - to choose the internal calibration system which sends a calibrated > > pulse to the inputs of selected chains; > > - to perform boundary scan. > > > > For the SSD layers, the ALICE experiment needs a readout circuit having very > > large dynamic range (+/-15 Mips) with good linearity and an adjustable > > shaping time from 1.4 us to 2.0 us. This is a challenge for such a circuit > > designed in a deep submicron process operated at only 2.5 V which is the edge > > of the use of standard analog design techniques. > > > > This paper will explain how the required specifications have been met: > > - single power supply; > > - low noise; > > - low power consumption (mean power consumption of designed circuit for > > a readout cycle of 1 ms is around 300 uW/ch); > > - large dynamic input range (+/-15 Mips) with good linearity; > > - differential current output to improve EMC; > > - geometry adapted to Tape Automated Bonding. > > > > The authors also expect to present evaluations of the circuit which was > > submitted to foundry at the end of March. > > -- > _____________________________________________________ > Catherine DECOSSE > CERN > Alice Experiment > CH-1211 Geneva 23 > > Office: 301 R-035 > Tel. +41 22 767 36 77 > Fax. +41 22 767 94 80 > Subject: Re: Corrected abstract and summary Date: Wed, 02 May 2001 08:25:43 -0500 From: Gabriele_Chiodini To: Catherine DECOSSE Hops, Sorry. The title is: Radiation tolerance studies of BTeV pixel readout chip prototypes Thank you. Gabriele Chiodini Catherine DECOSSE wrote: > Dear Gabriele, > > Thank you for your submission. > Would you please send me the title? > Regards > Catherine > > Gabriele_Chiodini wrote: > > > > Sorry, but we added a small correction to the abstract and summary > > just send it. > > > > Here it is the new abstract and summary of our contribution to the > > workshop. > > > > Abstract: > > We report on several irradiation studies > > performed on BTeV pixel readout chip prototypes exposed to > > a 200 MeV proton beam at Indiana University Cyclotron Facility. > > The pixel readout chip preFPIX2 has been developed at Fermilab > > for collider experiments and implemented in standard > > 0.25 um CMOS technology following radiation tolerant design rules. > > The tests confirmed the radiation tolerance > > of the chip design to proton total dose up to 14 MRad. > > In addition, non destructive radiation-induced single event upsets > > have been observed in on-chip static registers and the single bit > > upset cross section has been measured. > > We also show irradiation test results > > that we are planning to do on June-July 2001, > > where preFPIX2 readout chips bump-bonded to > > pixel sensors will be exposed to high dose. > > > > Summary: > > The BTeV experiment is planned to run at the Tevatron > > collider in ~2006. > > It is design to cover the ``forward'' region of the > > p-antip interaction point at the expected > > luminosity of 2E32/s/cm**2$. > > The experiment will employ a silicon pixel vertex detector > > to provide high precision space points for > > on-line lowest level trigger impact parameter finding. > > The ``hottest'' chip, located at 6 mm from the beam, will experience a > > fluence of ~ 1E14/cm**2/y. > > This correspond to the highest radiation enviroments at > > ATLAS and CMS at LHC. > > A pixel detector readout chip (FPIX) has been developed at Fermilab > > to meet the requirement of Tevatron collider experiments. > > The preFPIX2 reppresents the most advanced iteration of very succesfull > > chip prototypes and has been realized in standard deep-submicron CMOS > > technology from two vendors. > > As demostrated by the RD49 collaboration at CERN, the above > > process can be made very radiation tolerant > > following specific design rules. > > > > We show results of radiation tests performed this year > > with preFPIX2 chip prototypes including both total dose and single event > > > > effects. > > The tests have been performed by exposing the chip to 200 MeV protons > > (at the Indiana University Cyclotron Facility). > > The comparison of the chip performace before and after exposure > > shows the high radiation tolerance of the design to hadrons up to > > ~ 14 Mrad total dose. > > Last year exposures to radiation from a Colbalt-60 source at Argonne > > National Lab > > already verified the high radiation tolerance to gamma radiation up to > > ~ 30 Mrad total dose. > > Total dose effects are not the only concern for reliable > > operation of the detector. > > Ionizing radiation can > > induce single event upset (SEU) effects, as unwanted logic state > > transition in a digital device, corrupting stored data. > > The single event upsets just described do not permanently > > alter the chip behavior, > > but they could result in data losses, > > shifts of the nominal operating conditions, and > > loss of the chip control. > > If the single event upset rate is particularly high > > it could be significantly mitigated by circuit hardering > > techniques. Instead, if it is not, it could be tollerated > > simply by a slow periodic downloading of potentially corrupted data > > or full system resetting in the worse case. > > During the irradiation tests, > > we observed single event upsets in the preFPIX2 registers > > and measured the rate. > > The measurements consisted of detecting bit error > > rates in the static registers controlling the readout chip > > front-end operating conditions and the pixel cell respons. > > The single bit upset cross section measured for the > > digital-analog-converter > > registers located on the chip periphery was sigma = 3.8(+/-1.2 +/- > > 0.2)E-16cm**2, > > while for the mask and charge-injection registers located inside each > > pixel > > cell was sigma = 2.0(+/-0.3+/-0.1)E-16cm**2 (where the first error is > > statistical and the second systematic due to uncertainty > > in the beam fluence). > > The implications of the estimated SEU rate in the BTeV pixel vertex > > detector are discussed. > > We would like also to report results from > > irradiation tests planned for June-July 2001 > > with single chip sensor bump-bonded to a readout chip. > > In these future test, the primary goals are to increase the statistics > > of single event upsets and compare the front-end performance > > before and after irradiation of the assembly sensor-readout chip. > > > > Thanks, > > Gabriele > > > > -- > > Gabriele Chiodini Particle Physics Division, MS#122 (WH 10W) > > chiodini@fnal.gov Fermi National Accelerator Laboratory > > Phone: (630) 840-5151 P.O. Box 500 > > Fax: (630) 840-3867 Batavia, IL 60510 > > -- > _____________________________________________________ > Catherine DECOSSE > CERN > Alice Experiment > CH-1211 Geneva 23 > > Office: 301 R-035 > Tel. +41 22 767 36 77 > Fax. +41 22 767 94 80 -- Gabriele Chiodini Particle Physics Division, MS#122 (WH 10W) chiodini@fnal.gov Fermi National Accelerator Laboratory Phone: (630) 840-5151 P.O. Box 500 Fax: (630) 840-3867 Batavia, IL 60510 Subject: correction for LEB2001 paper Date: Wed, 2 May 2001 16:34:57 +0200 From: "Molnar Jozsef" To: Dear Catherine, My colleague Andras Fenyvesi () sent a paper for LEB 2001 with title "Neutron radiation tolerance tests of optical and opto-electronic components for the CMS Muon Barrel Alignment" on Saturday, April 28. Unfortunately he missed one author (D. Novak from Royal Institute of Technology) from the list. I corrected the text and attached the new file. Hopefully I did't couse big trouble for You. Sincerely Yours, /josef Name: Decosse.doc Decosse.doc Type: Microsoft Word Document (application/msword) Encoding: base64 Download Status: Not downloaded with message Subject: LEB 2001 workshop Date: Wed, 02 May 2001 17:06:44 +0200 From: alessandro bartoloni To: catherine.decosse@cern.ch Dear Mrs Decosse, attached to this email there are abstract and summary (both in word and ASCII) of a paper that I would like to submit to the LEB2001 workshop. I apologize for the delay. best regards Alessandro Bartoloni ################################### Alessandro Bartoloni I.N.F.N. Sezione di Roma Ple Aldo Moro 2 - 00185 - Roma phone +39-0649913535/4423 cell. +39-347-3730183 fax +39-06-4957697 email : alessandro.bartoloni@roma1.infn.it ################################## --------------------------------------------------------------------- Name: LEB01_1.doc LEB01_1.doc Type: Microsoft Word Document (application/msword) Encoding: base64 Download Status: Not downloaded with message Name: LEB01_1.txt LEB01_1.txt Type: Plain Text (text/plain) Encoding: quoted-printable Subject: LEB2001 abstract rectification Date: Wed, 2 May 2001 17:24:05 +0200 (MET DST) From: Franco Gonella To: Catherine.Decosse@cern.ch Dear Mrs. Catherine, I made an error in the list of authors with istitutions. Please, can you correct the previous text with this? Authors list with Institutions: Franco Gonella from Dip. di Fisica dell'Universita' di Padova and Sezione INFN di Padova, Padova, Italy Matteo Pegoraro from Sezione INFN di Padova, Padova, Italy Thanks and sory for the mistake. With my best regards, Franco Gonella. Subject: abstract for a poster presentation at LEB2001 Date: Wed, 02 May 2001 17:29:16 +0200 From: Per GALLNO Organization: CERN To: Catherine Decosse Dear Catherine, Please find below the abstract for a poster that I intend to present at LEB2001 in Stockholm: Best regards, Per ===================================================================== THE ATLAS READ OUT DATA FLOW CONTROL MODULE AND THE TTC VME INTERFACE PRODUCTION STATUS. Per Gällnö, CERN, Geneva, Switzerland (email: per.gallno@cern.ch) Abstract The ATLAS detector data flow from the Front End to the Read Out Buffers (ROD) has to be controlled in order to avoid that the ROD data buffers get filled up and hence data getting lost. This is achieved using a throttling mechanism for slowing down the Central Trigger Processor (CTP) Level One Accept rate. The information about the state of the data buffers from hundreds of ROD modules are gathered in daisy-chained fan-in ROD-BUSY modules to produce a single Busy signal to the CTP. The features and the design of the ROD-BUSY module will be described in this paper. The RD-12 TTC system VMEbus interface, TTCvi, will be produced and maintained by an external electronics manufacturer and will then be made available to the users from the CERN Electronics Pool. The status of this project is given. --------------------------------------------------------------------- Name: abstract.doc Type: Microsoft Word Document abstract.doc (application/msword) Encoding: base64 Download Status: Not downloaded with message Per Gällnö CERN EP/ATE Per Gällnö CERN EP/ATE Geneve Cellular: +41 (0)79 4527065 CH-1217 Fax: +41 (0)22 7679495 Switzerland Home: +41 (0)22 7821267 Work: +41 (0)22 7672404 Additional Information: Last Name Gällnö First Name Per Version 2.1 Subject: Date: Wed, 2 May 2001 17:31:26 +0200 (MET DST) From: Andrea Salamon To: catherine.decosse@cern.ch Dear Madam I would like to submit a paper for the 7th Workshop on Electronics for LHC Experiments. Abstract and conclusion of the submitted papers are sent in attachment. Best reguards Andrea Salamon --------------------------------------------------------------- Andrea Salamon INFN Rome and Universita` degli Studi di Roma "La Sapienza" Tel: +39-06-49914223 Fax: +39-06-49914320 E-mail: andrea.salamon@roma1.infn.it --------------------------------------------------------------- --------------------------------------------------------------------- Name: leb2001.txt leb2001.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64 Subject: Re: call for paper LECC2001 Date: Thu, 3 May 2001 00:19:42 +0200 (MDT DST) From: Piotr Malecki To: Catherine DECOSSE CC: dabrowsk@ftj.agh.edu.pl, Jan.Bohm@cern.ch, Marko.Mikuz@ijs.si, Stefan Koperny , Edward Gornicki Dear Catherine, with some delay but also with some hope for your mercy I am sending the title, abstract and summary of a paper and an eventual presentation for the coming LEB Workshop. I think that it fits the topic " Low voltage and high voltage distribution " I will still own you the full list of authors. That is not difficult to make but an explosion of vacations these days prevents me from having all necessary confirmations. With best wishes, Piotr ------------------------------------------------------------- - the title "Power Supply and Power Distribution System for the ATLAS Silicon Strip Detectors" - the abstract "The Silicon Strip Detector of the ATLAS experiment has modular structure. The granularity of its power supply system follows the granularity of the detector. This system of 4088 multi-voltage channels providing power and control signals for the readout electronics as well as bias voltage for silicon detectors is described. Problems and constraints of the power distribution lines are also presented. In particular, optimal choice between concurrent requirements on material, maximum voltage drop, space available for services, technological constraints and cost are discussed" - the summary The multi-voltage power supply system of the ATLAS SCT provides high current (of the order of 1 A) low voltages for analog and digital parts of the module readout chips as well as a number of low current voltages and control signals for the optical data transmission and clock distribution circuits. Low voltage power supply modules are associated with the high voltage modules which provide bias voltage (up to 500 V) for silicon detectors. Integration of low and high voltage power supply modules is on the level of a common crate equipped with a custom backplane, custom inter-module communication protocol, a common crate controller and a common crate bulk supply. One crate consists of 48 independent, fully isolated power supply channels. Common LV/HV power supply crates communicate with higher level of the Detector Control System (DSC) via the CAN bus protocol. Power supply modules are located outside of the ATLAS detector. Every SCT module is serviced by a multiwire cable/tape which consists of two pairs of high current lines, two pairs of the corresponding sense wires and a number of low current lines. This power transmission path is divided on three parts. The first part running from detector modules through the innermost part of the detector is made of thin aluminum-Kapton tapes, called low_low_mass tapes. Similar material constraints resulted in the choice of low_mass tapes for the second part of the power transmission lines. Conventional, but custom design copper multiwire cables are applied in the third part of that path. Many details of the design of the power supply units are closely related to parameters of the power transmission lines. The optimal selection of these parameters on the other hand is the subject for dificult compromises. In this paper we summarize the main requirements, specifications for the SCT power supply and transmission system, present design concepts of both, low and high voltage power modules and concentrate on integration solutions. An optimization process for the selection of the tranmission line parameters and its feed back on the power supply system design is also discussed. ----------------------------------------------------------------- Piotr MALECKI, Institute of Nuclear Physics, ATLAS Experiment Lab. 30-055 Krakow, ul Kawiory 26A tel:(48 12) 633 33 66 fax: (48 12) 633 38 84 home: (48 12) 4 226 227 mobile: +48 503 002 318 Subject: Re: Paper for LEB2001 Date: Thu, 03 May 2001 09:43:59 +0200 From: Miguel Ullan To: Catherine DECOSSE Dear Catherine, there are a few changes that we would like to make on the paper that we submitted last friday. The main one is the title, which we would like to change for: "LOW DOSE RATE EFFECTS AND IONIZATION RADIATION TOLERANCE OF THE ATLAS TRACKER FRONT-END ELECTRONICS" and some other minor word corrections. I include the corrected abstract and summary as text attachments. We would appreciate if you could include them as the final submissions even though we know that the deadline for submitions is over. Regards, Miguel. At 11:33 30/04/01 +0200, you wrote: >Dear Miguel, > >Thank you for your submission >Regards >Catherine > >Miguel Ullan wrote: > > > > Dear Madam, > > > > Here is a contribution to LEB 2001. I attach the abstract and summary as > > ASCII files and also paste them below. > > > > The main author is Miguel Ullan (Miguel.Ullan@cnm.es) who belongs to the > > Santa Cruz Institute for Particle Physics (SCIPP) at the University of > > California at Santa Cruz (UCSC). > > > > Best regards, > > > > Miguel Ullan > > > > > -------------------------------------------------------------------------------------- > > > > IONIZATION RADIATION TOLERANCE OF THE ATLAS TRACKER ELECTRONICS > > > > M. Ullan*, D. Dorfan*, T. Dubbs*, A. A. Grillo*, E. Spencer*, A. Seiden*, > > H. Spieler**, M. Gilchriese**, M. Lozano*** > > > > * Santa Cruz Institute for Particle Physics (SCIPP) > > University of California at Santa Cruz > > Santa Cruz, CA 95064 > > USA > > Phone: 1 831 459 3567 > > Fax: 1 831 459 5777 > > E-mail: ullan@scipp.ucsc.edu > > > > ** Lawrence Berkeley National Laboratory (LBNL) > > University of California at Berkeley > > Berkeley, California, USA > > > > *** Centro Nacional de Microelectrónica (CNM-CSIC) > > Barcelona, Spain > > > > Abstract > > > > Ionization damage has been investigated in the IC designed for the readout > > of the detectors in the Semiconductor Tracker (SCT) of the ATLAS experiment > > at the LHC, the ABCD chip. The technology used in the fabrication has been > > found to be free from Low Dose Rate Effects which facilitates the studies > > of the radiation hardness of the chips. Other experiments have been done on > > the individual transistors in order to study the effects of temperature and > > the annealing, and to get a better understanding and a quantitative > > information about these mechanisms. With all this information, the suitable > > irradiation experiments have been designed for the chips to obtain a better > > answer about the survivability of these chips in the real conditions. > > > > Summary > > > > The ABCD chip is the IC that has been designed for the readout of the > > silicon detectors of the ATLAS Semiconductor Tracker (SCT) at the LHC. It > > is fabricated on the DMILL technology, which is a BiCMOS process on an SOI > > substrate. This chip will have to be placed very close to the detectors > > and, therefore, inside the active area of the SCT. That means that it will > > have to endure the same level of radiation that the detectors themselves. > > > > Different experiments have been carried out to study the radiation hardness > > of this technology and the ABCD chip itself to that high level of > > radiation. The physical mechanisms that intervene in the damage produced on > > the analog part of these chips from ionization or non-ionization radiation > > are different and it is better to study them separately to have a good > > understanding of the problem. This study is presented here where the > > effects of ionization radiation have been analyzed for the DMILL technology > > and the ABCD chip, taking into account the total dose effects. > > > > A first study has been to check if the bipolar transistors of the DMILL > > technology suffer from Low Dose Rate Effects (LDRE) which would largely > > complicate the rest of radiation hardness studies. Different radiation > > experiments have been carried out up to a high enough total dose and at a > > very wide range of dose rates using individual transistors of the > > technology. The result has demonstrated that the DMILL technology does not > > suffer from total dose effects which facilitates the realization of other > > radiation hardness studies. This result has been confirmed by other > > irradiations up to the total dose of interest. Together with this study, > > the annealing of the damage produced on the transistors has been > > investigated in order to separate this effect from the LDRE. > > > > Other experiments have been carried out at different temperatures in order > > to obtain the sensitivity of the radiation damage of these chips to > > temperature. The tests structures have been irradiated up to the total dose > > of interest and at a wide range of temperatures from 10 to 110 ºC. The > > results demonstrate the presence of two opposite effects. One is the > > increase in the damage at higher temperatures, and the other is the > > increase in the annealing of that damage also for higher temperatures. This > > two effects result in a worst case temperature at which the transistors > > suffer the largest damage, being the damage smaller at higher or lower > > temperatures. > > > > Finally the ABCD chip has been irradiated up to the total dose and at a > > high dose rate in order to obtain the total ionization damage that will be > > produced to the chip in the real experiment. Given that it has been > > demonstrated that there are not LDRE on this technology this experiment can > > be done at a high dose rate and in a short period of time. The results > > demonstrate that the ABCD chip remain within specifications after the > > expected ionization damage has been produced. > > > > > -------------------------------------------------------------------------------------- > > > > > ------------------------------------------------------------------------------------------ > > > > abstract.txtName: abstract.txt > > Type: Plain Text (text/plain) > > > > Name: summary.txt > > summary.txt Type: Plain Text (text/plain) > > Encoding: quoted-printable > > > > > ------------------------------------------------------------------------------------------ > > > > > ------------------------------------------------------------------------------------------- > > Miguel Ullán Comes > > > > Centro Nacional de Microelectrónica (CNM-IMB) > > Consejo Superior de Investigaciones Científicas (CSIC) > > Campus UAB, Bellaterra, Cerdanyola > > 08193 Barcelona > > Spain > > > > Tf: + 34 93 594 7700 > > Fax: + 34 93 580 1496 > > e-mail: Miguel.Ullan@cnm.es > > http://www.cnm.es > > > ------------------------------------------------------------------------------------------- > >-- >_____________________________________________________ >Catherine DECOSSE >CERN >Alice Experiment >CH-1211 Geneva 23 > >Office: 301 R-035 >Tel. +41 22 767 36 77 >Fax. +41 22 767 94 80 --------------------------------------------------------------------- abstract.txtName: abstract.txt Type: Plain Text (text/plain) Name: summary.txt summary.txt Type: Plain Text (text/plain) Encoding: quoted-printable --------------------------------------------------------------------- ------------------------------------------------------------------------------------------- Miguel Ullán Comes Centro Nacional de Microelectrónica (CNM-IMB) Consejo Superior de Investigaciones Científicas (CSIC) Campus UAB, Bellaterra, Cerdanyola 08193 Barcelona Spain Tf: + 34 93 594 7700 Fax: + 34 93 580 1496 e-mail: Miguel.Ullan@cnm.es http://www.cnm.es ------------------------------------------------------------------------------------------- Subject: RE: call for paper LECC2001 Date: Thu, 3 May 2001 11:12:50 +0200 From: "Ruud Kluit" Reply-To: To: "Catherine DECOSSE" Hi Catherine, The author list was not in the abstract and summary file I had sent you last week. So hereby a new version. Regards, Ruud. > -----Original Message----- > From: owner-lhc-proj-leb-workshop@listbox.cern.ch > [mailto:owner-lhc-proj-leb-workshop@listbox.cern.ch]On Behalf Of > Catherine DECOSSE > Sent: Tuesday, April 24, 2001 5:28 PM > To: lhc-proj-leb-workshop@listbox.cern.ch > Subject: call for paper LECC2001 > > > 7th WORKSHOP ON ELECTRONICS FOR LHC EXPERIMENTS > STOCKHOLM, Sweden, 10-14 September 2001 > > =========================================================== > REMINDER: DEADLINE for submission of Abstracts is April 30 !!!! > =========================================================== > > http://www.sysf.physto.se/leb2001 > > Regards > Catherine Decosse > > --------------------------------------------------------------------------- > 7th Workshop on Electronics for LHC Experiments > 10-14 September 2001, Stockholm, Sweden > > CALL FOR PAPERS > --------------- > > The purpose of the workshop is to review the electronics for LHC experiments > and to identify areas and encourage common efforts for the development of > electronics within and between the different LHC experiments and to promote > collaboration in the engineering and physics communities involved in the > LHC activities. > > The programme of the workshop will include both invited plenary talks and > parallel working groups for contributed papers, complemented by a poster > session. > The focus of the workshop will be research and recent development in the > following topics: > > Radiation and magnetic field tolerant electronics systems > Optoelectronics and data transfer systems > Detector control and real time systems > Packaging and interconnections > Electronics production and test techniques > Systems reliability and quality assurance > Hardware and embedded software maintenance > Electronics for trackers > Electronics for calorimeters > Electronics for muon detectors > Trigger electronics > Low voltage and high voltage distribution > Grounding, shielding cooling and alignment > > Authors are invited to submit papers describing original developments and > new contributions in the topic areas. Manufacturers are welcome to submit > abstracts on new, state of the art, electronic products or systems, > in the field of electronic technology for particle physics. > > Abstracts (100 words long) and summaries (500 words long) in ASCII format > and without figures must be submitted by electronic mail to: > > Catherine Decosse > Email: Catherine.Decosse@cern.ch > > The summary should be complete and describe the work, its relevance > to experiments at LHC (including specific experiment(s) if applicable) > and important conclusions. > > > Deadline for the submission is: > 30 April 2001 > > An acknowledgement will be sent by Email to the corresponding Author. > > Abstracts and summaries will be made available at the time of the workshop: > these will include papers which cannot be granted an oral presentation because > of time constraints but which, in the view of the programme committee, > are of interest to the community. Workshop records will be made available. > > Workshop Secretariat: > > Samuel Silverstein > University of Stockholm > Department of Physics > Box 6730, SE-113 85 STOCKHOLM > Email: silver@physto.se > tel. +46 8 16 46 65 > fax. +46 8 16 45 80 > > Any further information and news on the workshop will be provided > at the following URL address : > > http://www.physto.se/leb2001 > > To be registered in our database of the workshop, > please email your name and address to : > > Jonas Klereborn > Email: klere@physto.se > > > -- > _____________________________________________________ > Catherine DECOSSE > CERN > Alice Experiment > CH-1211 Geneva 23 > > Office: 301 R-035 > Tel. +41 22 767 36 77 > Fax. +41 22 767 94 80 > --------------------------------------------------------------------- Name: Abstract+summary.doc Type: Microsoft Word Document Abstract+summary.doc (application/msword) Encoding: base64 Download Status: Not downloaded with message Subject: Re: Papers for LEB Date: Thu, 03 May 2001 10:58:53 +0100 From: Eric Eisenhandler To: Catherine DECOSSE Dear Catherine, I attach our three papers as plain text files. Please let me know if there are any problems with the format. The one on the multi-chip module (MCM) will be presented by Werner Hinderer of Heidelberg (his email address is given on the paper) and he should also be the contact author. For the other two, we are not yet decided who will give the paper. We still need to sort out exactly who is going to the workshop. The contact author for the paper on the readout module (ROD) is Viraj Perera of RAL, and for the "one size fits all" paper (CMM) it is me. Thanks very much for your help and for relaxing the deadline a bit. Best regards, Eric ============================================================== Eric Eisenhandler e.eisenhandler@qmw.ac.uk Physics Dept. http://hepwww.ph.qmw.ac.uk/~efe/EElinks.html Queen Mary, QMW: Tel +44 (0)20-7882-5033 University of London Fax +44 (0)20-8981-9465 Mile End Road RAL: Tel +44 (0)1235-44-5562 London E1 4NS, UK Fax +44 (0)1235-44-6733 ============================================================== --------------------------------------------------------------------- Name: LEB_MCM.txt LEB_MCM.txt Type: Microsoft Word Document (application/msword) Encoding: base64 Name: LEB_ROD.txt LEB_ROD.txt Type: Microsoft Word Document (application/msword) Encoding: base64 Name: LEB_CMM.txt LEB_CMM.txt Type: Microsoft Word Document (application/msword) Encoding: base64 Subject: abstract to LEEC-2001 Date: Fri, 4 May 2001 15:45:54 +0400 (MSD) From: Grigori Feofilov To: Catherine DECOSSE CC: Paolo Giubellino , Paul Kuijer , Beppe Giraudo , Ton van den Brink , Franco Daudo , Flavio Tosello 0039-11-6707413/5 , Serguei Igolkine , godisov@nataly.spb.su, Gert-Jan Nooren , silvia coli , Paic Guy Dear Catherine, This is the absract in the final form of one report to LEEC2001. Best regards, Grigori Feofilov -------------------------------------------------------------------- "Conductive cooling of SDD and SSD Front-End chips for ALICE" -------------------------------------------------------------------- A.van den Brink(a), F.Daudo(b), S.Coli(b), G.Feofilov(c), G.Giraudo(b), O.Godisov(d), S.Igolkin(d), P.Kuijer(a), G.-J.Nooren(e), A.Swichev(d), F.Tosello(b) a/Utrecht University, Netherlands b/INFN, Torino,Italy c/St.Petersburg State University, Russia d/CKBM,St.Petersburg, Russia e/NIKHEF, Amsterdam, Netherlands Reporter: G.Feofilov (For the ALICE collaboration) Abstract -------------- We present analysis, technology developments and test results of the heat drain system of the SDD and SSD front-end electronics for the ALICE Inner Tracker System (ITS). The application of the super thermoconductive carbon fibre thin plates provides a practical solution for the development of miniature motherboards for the FEE chips situated inside the sensitive ITS volume. Unidirectional carbon fibre motherboards of 160 -300 micron thickness ensure the mounting of the FEE chips and the efficient heat sink to the cooling arteries. Thermal conductivity up to 1.3 times better then copper is achieved while preserving a negligible multiple scattering contribution by the material (less then 0.07-0.15 percent of X/Xo). ----------------------------------------------- Summary ----------------------------------------------- 1) State-of-the art Front-end electronics of coordinate-sensitive Si detectors of ALICE at the LHC is situated inside the Inner Tracking System region. Therefore the heat drain of about 7kW of power is to be done under the stringent requirement of minimisation of any materials placed in this area. Analysis of various possible cooling schemes was performed earlier as a starting point of the general ITS services design. The application of super thermoconductive carbon fibre plastics was proposed in order to get the most efficient integration of the extremely lightweight FEE motherboards and the local heat sink units. ANSYS simulations show the value of temperature gradients along the boards which are in line with the requirements of the systematic aspects of detector performance (gradients of less then 1 degree C). 2) The implementation of these ideas in a single unit called "the heat bridge" required the development of a new technology of thin unidirectional carbon fibre plates manufacturing. This technology was successfully developed and is being progressing further at present. The application of super thermoconductive fibre Thornell KX1100 for this purpose is the key point. The conductivity along the fibre is about 1100W/M/K, while the mechanical strength is ensured at the level of steel. The thermal expansion coefficient of the carbon fibre based compounds is very low (close to zero), meaning the mechanically stabilised devices. The flat carbon unidirectional fibre plates were manufactured ranging in thickness from 150 to 330 microns. The dimensions of the plates used could be from 1*7 - to 10*10 cm2. Summary of the different configurations of heat bridges produced is presented. Various types of surface coatings were also tested: pure carbon fibre surfaces and insulating Al ceramics coatings. The carbon fibre heat bridge surface quality tests were done for a batch of CF plates. The roughness of the surface was measured and found to better than 10 microns. The choice of technology for ALICE SDD and SSD FEE chips was performed. The prototype heat bridges were tested for mounting and microcable bonding technology. 3) Thermal conductivity tests were performed for a variety of heat bridges. Results show the performance of the best samples at the level of 1.3 of copper of the same geometry. Subject: leb2001 abstract and summary Date: Sat, 05 May 2001 01:45:30 +0200 From: Michal Ziolkowski Organization: Univ. of Siegen To: Catherine.Decosse@cern.ch Title: ----- Radiation-hard ASICs for optical data transmission in the ATLAS Pixel detector Authors: ------- K.E. Arms, K.K. Gan, M. Johnson, H. Kagan, R. Kass, C. Rush, S. Smith and M. Zoeller Department of Physics, The Ohio State University, Columbus, Ohio 43210, USA J. Hausmann, M. Holder, M. Kraemer, A. Niculae and M. Ziolkowski * Fachbereich Physik, University of Siegen, 57068 Siegen, Germany *corresponding author: e-mail michal.ziolkowski@cern.ch Abstract: -------- The aim of our work is to design radiation-hard CMOS electronics for optical data transmission in the ATLAS Pixel detector. Two ASICs are under development: a VCSEL driver chip for 80 Mb/s data transmision from the detector and a Bi-Phase Mark decoder chip to recover control data and 40 MHz clock received optically by a PIN diode on the detector side. Both ASICs are implemented in radiation-hard 0.8um DMILL technology. Samples of chips were irradiated recently with 25 GeV protons up to the total dose of 55 Mrad and the conclusive results are expected in the Summer of 2001. Summary: ------- Originally the optical driver and Bi-Phase Mark decoder ASICs have been designed by SemiConductor Tracker community and have been implemented in AMS 0.8 um npn Bi-Polar process. In order to satisfy the needs of the Pixel community we have re-designed both circuits and fabricated them in DMILL radiation-hard CMOS technology providing low power dissipation and enabling assembling flexibility. First encouraging results are now available. Most of the ASICs can survive up to an irradiation dose of 55 Mrad in the initial irradiation trial. As expected, unfavorable effects of irradiation in the decoder chip are compensated by increased supply voltage: from 3.2 V initially - up to 5.0 V after total exposure. Detailed comparison of the decoder chip characteristics before and after irradiation will be carried out by mid of May,~2001, following post-irradiation samples release. In particularly low input current threshold found before exposure will be re-examine. Also the VCSEL driver chip has sustained its good performance during irradiation trial. Minor bright current drop after irradiation is easily correctable by means of tuned bias current whereas the observed increase of dim current is a favorable change, since irradiated VCSELs show higher bias threshold. Third DMILL iteration of Bi-Phase Mark decoder chip is now in preparation. The performance at low input current will be equalized by including a feedback circuit for voltage offset correction. Three independent decoder channels will be arranged on single chip as required by array-like assembling plan. New DMILL samples will be under tests in early October 2001. In addition to DMILL implementation, we have recently designed both ASICs in a deep submicron 0.25um technology with expectation to minimize power dissipation and to achieve very good inherent radiation tolerance. First samples will be evaluated in June 2001. Subject: sostituzione abstract Date: Mon, 7 May 2001 10:42:00 +0200 (MET DST) From: Angelo Rivetti To: Catherine.decosse@cern.ch Ciao Catherine, il 30 aprile avevo inviato un abstract per la conferenza LEB2001. Mi e' stato chiesto di apportare alcune correzioni. Ti invio il nuovo abstract, (SDDTo_1.txt), che, se possibile, ti chiederei di sostituire a quello inviato in precedenza (SDD_To.txt). Se non si puo', pazienza... Grazie anticipatamente e scusa il disturbo. angelo --------------------------------------------------------------------- Name: SDDTo_1.txt SDDTo_1.txt Type: Plain Text (text/plain) Encoding: BASE64 Subject: avec les fichiers ! Date: Mon, 7 May 2001 14:06:57 +0100 (WET DST) From: lecoq@clermont.in2p3.fr To: Catherine.Decosse@cern.ch ----- Begin Included Message ----- From lecoq@clermont.in2p3.fr Mon May 7 14:05 WET 2001 Date: Mon, 7 May 2001 14:05:00 +0100 (WET DST) From: lecoq@clermont.in2p3.fr To: Catherine.Decosse@cern.ch Subject: Re: call for paper LECC2001 Cc: lecoq@clermont.in2p3.fr Chere Catherine, Voici (enfin) l'abstract de la presentation orale que j'espere donner a Stocholm. Je te le donne sous forme MSWORd (en .doc), et aussi sous forme postscript (.ps). Je m'excuse pour le retard, mais j'ai ete en mission presque toutes les semaines ! J'ecris aussi le resume de 500mots, tu devrais l'avoir mercredi. Bien amicalement, Jacques Lecoq ----- End Included Message ----- --------------------------------------------------------------------- Name: lerb2001.doc lerb2001.doc Type: Microsoft Word Document (application/msword) Encoding: x-uuencode --------------------------------------------------------------------- lerb2001.psName: lerb2001.ps Type: Postscript Document (application/postscript) Subject: 7th Workshop on Electronics for LHC Experiments Date: Mon, 07 May 2001 18:43:49 -0400 From: Marco Leite Organization: None To: Catherine.Decosse@cern.ch, leite@bnl.gov Dear Mrs. Decosse, We would like to send the paper below for the workshop. Please, accept our sincere apologies for any inconvenience this delay may cause. If you need any further information, please don't hesitate to contact me. Thank you for your kind attention, MARCO LEITE leite@bnl.gov ---------------------------------------------------------------------------- Optically Coupled Charge Injection System for Ionization Based Radiation Detectors H. Chen, F. Lanni, M.A.L. Leite, S. Rescia and H. Takai Brookhaven National Laboratory - Physics Department Upton, NY - 11973 - USA Abstract An optically coupled charge injection system for ionization based radiation detectors which allows a test charge to be injected without the creation of ground loops has been developed. An ionization like signal from an external source is brought into the detector through an optical fiber and injected into the detector electrodes by means of a photodiode. Summary For the performance tests of ionization based radiation detectors it is desirable to have a system which is capable of injecting a charge of known value in a condition that is as close as possible to the operating environment, where charge is locally generated by the ionization of the sensitive media in the detector. One of the main problems with the conventional approach of the direct injection through an electrical cable connected to the detector electrodes is the change of the detector electrical characteristics. In particular, the grounding configuration of the system can be completely modified by the introduction of the injection circuit new ground path. The use of an optically coupled injection, in which a light to current converter is placed on the electrodes of the detector to generate the ionization signal, allows for a full galvanic isolation between the detector and the test pulser. A photodiode installed on the electrodes and biased by means of the high voltage system achieves the light to current conversion. It has a capacitance of only a few pf, small if compared with detector capacitances of the order of nF. The photodiode should also have a fast time response and low dark current. Size is also an issue, as this device may needs to fit in spaces of only a few millimeters. The light, generated by a laser diode stimulated to produce a suitable signal for the detector, is brought to the photodiode using a multimode optical fiber. As an example of this method, the ATLAS Electromagnetic Liquid Argon Calorimeter test stand at BNL has been modified by adding photodiodes on several electrodes. The optical signal is created using a light pulse generator whose output is modulated to produce the same triangular shaped pulse generated by an ionization signal. Crosstalk studies can also be performed by injecting one electrode and recording the crosstalk pattern on neighbor channels. Results of measurements showing how the detector-readout system can be characterized based on the analysis of the signal shape and how the crosstalk at several system levels can be evaluated in this particular case will be presented. ---------------------------------------------------------------------------------- Subject: Re: Still in time for one paper for the Conference? Date: Tue, 8 May 2001 11:46:07 +0200 (MET DST) From: Roberto Beccherle To: Catherine DECOSSE Hi Catherine, sorry for the delay. Here is the Abstract and the Summary of the paper entiteled: Design and Test of a DMILL Module Controller Chip for the Atlas Pixel Detector Best regards, Roberto Beccherle -- E-Mail: Roberto.Beccherle@ge.infn.it Mail-Address: INFN - Sez. di Genova Phone: +39 10 353-6485 Via Dodecaneso, 33 Fax: +39 10 353-6319 I-16146 GENOVA --------------------------------------------------------------------- Name: leb2001.txt leb2001.txt Type: Plain Text (TEXT/PLAIN) Encoding: BASE64